| Optimization of turning parameters using firefly algorithm B Rajan Journal of Applied Sciences 12 (10), 1038-1042, 2012 | 25* | 2012 |
| Multi objective optimization of machining parameters for hard turning OHNS/AISI H13 material, using genetic algorithm NS Narayanan, N Baskar, M Ganesan Materials Today: Proceedings 5 (2), 6897-6905, 2018 | 19 | 2018 |
| Effect of ZrO2 nano-particles on mechanical and corrosion behaviour of Al2024 alloy NSN EdwardKennedy, B.S.Sachin, M.Ramachandra, C.A.Niranjan, N.Sriraman ... Materials Today Proceedings, 2020 | 15* | 2020 |
| Performance of cutting tool with cross-chevron surface texture filled with green synthesized aluminium oxide nanoparticles VH Bn, R Sankaran Scientific Reports 9 (1), 1-9, 2019 | 15 | 2019 |
| Evaluation and optimization of surface roughness and metal removal rate through RSM, GRA, and TOPSIS techniques in turning PTFE polymers N Sathiya Narayanan, N Baskar, M Ganesan, MP Jenarthanan, ... Advances in Manufacturing Technology: Select Proceedings of ICAMT 2018, 595-605, 2019 | 15 | 2019 |
| Synthesis of bio-oil from waste Trichosanthes cucumerina seeds: a substitute for conventional fuel R Manimaran, K Murugu Mohan Kumar, N Sathiya Narayanan Scientific Reports 10 (1), 17815, 2020 | 12 | 2020 |
| Influence of thermomechanical processing on microstructure, mechanical and strain hardening properties of single-phase Mg-4Li-0.5 Ca alloy for structural application NSN N Sriraman, S Kumaran Journal of Magnesium and Alloys 8 (4), 1262-1268, 2020 | 12 | 2020 |
| Performance of ceramic cutting tool with groove and cross-chevron surface textures filled with semi-solid lubricants BNV Hari, NS Narayanan, N Baskar, N Sriraman, VSPS Nanduru Materials Today: Proceedings 63, 504-509, 2022 | 7 | 2022 |
| Mechanical characteristics of glass epoxy composites with Yttrium powder fillers N Sriraman, VM Sreehari, RJ Bharathi, NS Narayanan Materials Today: Proceedings 50, 2462-2466, 2022 | 6 | 2022 |
| Lean Manufacturing Techniques for Effective Utilization of Man Power in Engine Accessory Production Line BK N. Sathiya Narayanan, M. Anandha Raj, T. Ananth, S. Aravindh International Journal of Innovative Research in Science, Engineering and …, 2016 | 5 | 2016 |
| Performance of surface textured PCD inserts with wettability chemical solutions for machining operation G Sakthivel, NS Narayanan, BNV Hari, N Sriraman, ... Materials Today: Proceedings 46, 8283-8287, 2021 | 2 | 2021 |
| Comparison of static and thermal stress analysis on Mg AZ-63 textured and untextured material surfaces DGV Sriraman. N, Sathiya Narayanan. N, Arjun.P Materials Today:Proceedings, 2021 | 1 | 2021 |
| Tool wear investigation of micro-textured and non-textured carbide inserts for machining industrial component NS Narayanan, N Baskar, M Kok, R Sankaran, G AanandhaManikandan International Journal of Rapid Manufacturing 9 (4), 309-321, 2020 | 1 | 2020 |
| Contemporary Pedagogy Approach for Software-Based Laboratory Courses in Engineering Education SN Nagarajan, SN Venkata Sai Prabhu Proceedings of International Conference on Digital Pedagogies (ICDP), 2019 | | 2019 |
| Modelling and Simulation of Helical Fluid Flow through Double Start Screw Type Heat Exchanger RR R. Soorya Prakash, C. SugiSamraj, S. Syed Suheil International Journal of Engineering and Management Research 5 (6), 512-517, 2015 | | 2015 |
| Productivity Improvement in Steering Knuckle Machining Line Using Lean Principles KN R. Kumar, A.Maria Jackson International Advanced Research Journal in Science, Engineering and …, 2015 | | 2015 |
| Optimization of Drilling Parameters on Al 6061T6 using Firefly Algorithm Concurrent Advances in Mechanical Engineering 1 (1), 9-18, 2015 | | 2015 |
| Studies of thermal characterization of Hybrid Bio-mass Kalyankumar International Journal of Innovative Research in Science, Engineering and …, 2014 | | 2014 |
| CONSTRAINED MACHINING PARAMETERS OPTIMIZATION OF EN8 STEEL USING TAGUCHI APPROACH NS Narayanan, M Ganesan, VP Kumar, P Vijayakumar, N Baskar | | 2014 |
| APPLICATION OF TAGUCHI METHOD FOR OPTIMIZING SURFACE ROUGHNESS IN CNC TURNING OF EN 8 STEEL NB M. Ganesan, V. Prem Kumar, P. Vijayakumar IJIRT 1 (11), 440-445, 2014 | | 2014 |
Dr.S.Bharathi RajaProfessor & Dean, Engineering and Technology, Academy of Maritime Education & Training (AMET在 dsit.ac.in 的电子邮件经过验证
Dr.S.Bharathi RajaProfessor & Dean, Engineering and Technology, Academy of Maritime Education & Training (AMET在 dsit.ac.in 的电子邮件经过验证