| Inverse estimation of thermophysical properties for anisotropic composite SK Kim, BS Jung, HJ Kim, WI Lee Experimental Thermal and Fluid Science 27 (6), 697-704, 2003 | 78 | 2003 |
| Solution of inverse heat conduction problems using maximum entropy method SK Kim, WI Lee International Journal of Heat and Mass Transfer 45 (2), 381-391, 2002 | 66 | 2002 |
| Multi-scale filling simulation of micro-injection molding process SJ Choi, SK Kim Journal of Mechanical Science and Technology 25, 117-124, 2011 | 59 | 2011 |
| Injection molding of a nanostructured plate and measurement of its surface properties YE Yoo, TH Kim, DS Choi, SM Hyun, HJ Lee, KH Lee, SK Kim, BH Kim, ... Current Applied Physics 9 (2), e12-e18, 2009 | 52 | 2009 |
| Determination of three-dimensional permeability of fiber preforms by the inverse parameter estimation technique SK Kim, IM Daniel Composites Part A: Applied Science and Manufacturing 34 (5), 421-429, 2003 | 32 | 2003 |
| Injection molding of micro patterned PMMA plate YOO Yeong-Eun, KIM Tae-Hoon, JE Tae-Jin, C Doo-Sun, ... Transactions of Nonferrous Metals Society of China 21, s148-s152, 2011 | 28 | 2011 |
| Flow-rate based method for velocity of fully developed laminar flow in tubes SK Kim Journal of Rheology 62 (6), 1397-1407, 2018 | 26 | 2018 |
| A solution method for a nonlinear three-dimensional inverse heat conduction problem using the sequential gradient method combined with cubic-spline function specification SK Kim, JS Lee, WI Lee Numerical Heat Transfer: Part B: Fundamentals 43 (1), 43-61, 2003 | 25 | 2003 |
| Non-Newtonian modeling of contact pressure in fused filament fabrication SK Kim, DO Kazmer, AR Colon, TJ Coogan, AM Peterson Journal of Rheology 65 (1), 27-42, 2021 | 24 | 2021 |
| Solution to inverse heat conduction problem in nanoscale using sequential method SK Kim, IM Daniel Numerical heat transfer: part b: fundamentals 44 (5), 439-456, 2003 | 24 | 2003 |
| Observation of permeability dependence on flow rate and implications for liquid composite molding SK Kim, IM Daniel Journal of composite materials 41 (7), 837-849, 2007 | 22 | 2007 |
| Smart cure of thick composite filament wound structures to minimize the development of residual stresses DH Lee, SK Kim, WI Lee, SK Ha, SW Tsai Composites Part A: Applied Science and Manufacturing 37 (4), 530-537, 2006 | 22 | 2006 |
| Flow and heat transfer analysis during tape layup process of APC-2 prepregs HJ Kim, SK Kim, WI Lee Journal of Thermoplastic Composite Materials 17 (1), 5-12, 2004 | 22 | 2004 |
| Concurrent characterization of compressibility and viscosity in extrusion-based additive manufacturing of acrylonitrile butadiene styrene with fault diagnoses DO Kazmer, AR Colon, AM Peterson, SK Kim Additive Manufacturing 46, 102106, 2021 | 21 | 2021 |
| Flow and solidification of semi-crystalline polymer during micro-injection molding J Hong, SK Kim, YH Cho International Journal of Heat and Mass Transfer 153, 119576, 2020 | 21 | 2020 |
| Resolving the final time singularity in gradient methods for inverse heat conduction problems SK Kim Numerical Heat Transfer, Part B: Fundamentals 57 (1), 74-88, 2010 | 21 | 2010 |
| An inverse estimation of surface temperature using the maximum entropy method SK Kim, BS Jung, WI Lee International communications in heat and mass transfer 34 (1), 37-44, 2007 | 21 | 2007 |
| Determination of in‐plane permeability of fiber preforms by the gas flow method using pressure measurements SK Kim, JG Opperer, DH Kim, IM Daniel Polymer composites 24 (1), 34-44, 2003 | 21 | 2003 |
| Characterization of local preform defects in resin transfer molding by the gas flow method and statistical analysis JG Opperer, SK Kim, IM Daniel Composites science and technology 64 (13-14), 1921-1935, 2004 | 20 | 2004 |
| Optimal control of accelerator concentration for resin transfer molding process SK Kim, DH Kim, IM Daniel International journal of heat and mass transfer 46 (20), 3747-3754, 2003 | 20 | 2003 |
