Estimation of tool wear during CNC milling using neural network-based sensor fusion N Ghosh, YB Ravi, A Patra, S Mukhopadhyay, S Paul, AR Mohanty, ... Mechanical Systems and Signal Processing 21 (1), 466-479, 2007 | 490 | 2007 |
Growth of tool wear in turning of Ti-6Al-4V alloy under cryogenic cooling KA Venugopal, S Paul, AB Chattopadhyay Wear 262 (9-10), 1071-1078, 2007 | 385 | 2007 |
Beneficial effects of cryogenic cooling over dry and wet machining on tool wear and surface finish in turning AISI 1060 steel S Paul, NR Dhar, AB Chattopadhyay Journal of Materials Processing Technology 116 (1), 44-48, 2001 | 276 | 2001 |
Some studies on high-pressure cooling in turning of Ti–6Al–4V AK Nandy, MC Gowrishankar, S Paul International Journal of Machine Tools and Manufacture 49 (2), 182-198, 2009 | 212 | 2009 |
Tool wear in cryogenic turning of Ti-6Al-4V alloy KA Venugopal, S Paul, AB Chattopadhyay Cryogenics 47 (1), 12-18, 2007 | 209 | 2007 |
The influence of cryogenic cooling on tool wear, dimensional accuracy and surface finish in turning AISI 1040 and E4340C steels NR Dhar, S Paul, AB Chattopadhyay Wear 249 (10-11), 932-942, 2001 | 200 | 2001 |
Machining of AISI 4140 steel under cryogenic cooling—tool wear, surface roughness and dimensional deviation NR Dhar, S Paul, AB Chattopadhyay Journal of Materials Processing Technology 123 (3), 483-489, 2002 | 177 | 2002 |
Effects of cryogenic cooling by liquid nitrogen jet on forces, temperature and surface residual stresses in grinding steels S Paul, AB Chattopadhyay Cryogenics 35 (8), 515-523, 1995 | 170 | 1995 |
Role of cryogenic cooling on cutting temperature in turning steel NR Dhar, S Paul, AB Chattopadhyay Journal of Manufacturing Science and Engineering 124 (1), 146-154, 2002 | 167 | 2002 |
Modelling of specific energy requirement during high-efficiency deep grinding S Ghosh, AB Chattopadhyay, S Paul International Journal of Machine Tools and Manufacture 48 (11), 1242-1253, 2008 | 144 | 2008 |
Correlation between full width at half maximum (FWHM) of XRD peak with residual stress on ground surfaces M Vashista, S Paul Philosophical Magazine 93 (33), 4194-4209, 2012 | 142 | 2012 |
The effect of cryogenic cooling on grinding forces S Paul, AB Chattopadhyay International Journal of Machine Tools and Manufacture 36 (1), 63-72, 1996 | 140 | 1996 |
A study of effects of cryo-cooling in grinding S Paul, AB Chattopadhyay International Journal of Machine Tools and Manufacture 35 (1), 109-117, 1995 | 117 | 1995 |
Effect of substrate bias voltage on structural and mechanical properties of pulsed DC magnetron sputtered TiN–MoSx composite coatings S Gangopadhyay, R Acharya, AK Chattopadhyay, S Paul Vacuum 84 (6), 843-850, 2010 | 114 | 2010 |
Analytical and experimental modelling of the abrasive water jet cutting of ductile materials S Paul, AM Hoogstrate, CA Van Luttervelt, HJJ Kals Journal of Materials Processing Technology 73 (1), 189-199, 1998 | 107 | 1998 |
Determination and control of grinding zone temperature under cryogenic cooling S Paul, AB Chattopadhyay International Journal of Machine Tools and Manufacture 36 (4), 491-501, 1996 | 106 | 1996 |
Effects of grit blasting on surface properties of steel substrates KP Chander, M Vashista, K Sabiruddin, S Paul, PP Bandyopadhyay Materials & Design 30 (8), 2895-2902, 2009 | 105 | 2009 |
Numerical modelling of surface topography in superabrasive grinding S Chakrabarti, S Paul The International Journal of Advanced Manufacturing Technology 39 (1), 29-38, 2008 | 104 | 2008 |
An experimental investigation of rectangular pocket milling with abrasive water jet S Paul, AM Hoogstrate, CA Van Luttervelt, HJJ Kals Journal of Materials Processing Technology 73 (1), 179-188, 1998 | 90 | 1998 |
Effects of cryo-cooling in grinding steels S Paul, PP Bandyopadhyay, AB Chattopadhyay Journal of Materials Processing Technology 37 (1-4), 791-800, 1993 | 85 | 1993 |