Foaming Ability of Rotomolding Polyolefin Resins
R Pop-Iliev - Advanced Materials Research, 2014 - Trans Tech Publ
The main focus of the research presented in this paper is the investigation of the ability of
various polyolefin resins to be converted into integral-skin cellular composites by using the …
various polyolefin resins to be converted into integral-skin cellular composites by using the …
ANTEC 2009: Extrusion-assisted direct-foaming rotational molding process
K Christian, E Abdalla, G Eberle, R Pop-Iliev - Cellular Polymers, 2010 - go.gale.com
This paper focuses on the evolution and experimental validation of the novel patent-pending
Extrusion-Assisted Rotational Foam Molding (EARFM) process intended for the fabrication …
Extrusion-Assisted Rotational Foam Molding (EARFM) process intended for the fabrication …
Rotational foam molding of polypropylene with control of melt strength
R Pop‐Iliev, F Liu, G Liu, CB Park - Advances in Polymer …, 2003 - Wiley Online Library
Polypropylene (PP) has not been used extensively in rotational foam molding because it has
been traditionally considered as nonfavorable for foaming applications because of its …
been traditionally considered as nonfavorable for foaming applications because of its …
Effect of crystalline structure on the cell morphology and mechanical properties of polypropylene foams fabricated by core‐back foam injection molding
M Wu, F Wu, Q Ren, Z Weng, H Luo… - Journal of Applied …, 2021 - Wiley Online Library
Foam injection molding (FIM) is an advanced technology for preparing lightweight plastic
foams, but its inferior mechanical performance remains a challenge. In this study …
foams, but its inferior mechanical performance remains a challenge. In this study …
Processing of polypropylene foams in melt compounding based rotational foam molding
R Pop-Iliev, CB Park - Journal of reinforced plastics and …, 2002 - journals.sagepub.com
This paper is intended to provide an engineering understanding of the technological
potentials for processing polypropylene (PP) foams in rotational foam molding. A process …
potentials for processing polypropylene (PP) foams in rotational foam molding. A process …
Processing of fine-cell polypropylene foams in compounding-based rotational foam molding
R Pop-Iliev - 1999 - library-archives.canada.ca
This thesis is intended to provide a scientific and engineering understanding of the
technological potentials for processing fine-cell PP foams by using a compounding …
technological potentials for processing fine-cell PP foams by using a compounding …
Rotational foam molding of metallocene catalyzed polyethylene: CBA screening and process characteristics
M Emami, E Takacs… - Journal of cellular …, 2010 - journals.sagepub.com
The objective of this work is to investigate the effects of different chemical blowing agents
(CBAs) and processing conditions on the cellular structure of foamed metallocene …
(CBAs) and processing conditions on the cellular structure of foamed metallocene …
The importance of timely polymer sintering while processing polypropylene foams in rotational molding
Producing polypropylene (PP) foams with satisfactory cell morphologies in rotational foam
molding is feasible. However, the narrow interval between the melting temperature of PP …
molding is feasible. However, the narrow interval between the melting temperature of PP …
Chemical blowing agent-based processing of integral-skin polypropylene cellular composites in rapid rotational foam molding
R Pop-Iliev - AIP Conference Proceedings, 2019 - pubs.aip.org
The traditional rotational molding process is the most widely implemented technology for low-
cost fabrication of low-volumes of hollow/double-walled large-sized, seamless and virtually …
cost fabrication of low-volumes of hollow/double-walled large-sized, seamless and virtually …
Melt compounding based rotational foam molding technology for manufacture of polypropylene foams
R Pop-Iliev, CB Park - Journal of reinforced plastics and …, 2002 - journals.sagepub.com
This paper is intended to provide an engineering understanding of the technological
potentials for processing polypropylene (PP) foams in rotational foam molding. A process …
potentials for processing polypropylene (PP) foams in rotational foam molding. A process …