Microstructure understanding of high Cr-Ni austenitic steel corrosion in high-temperature steam
The microstructure and microchemistry of the oxide scales formed on Fe-21Cr-32Ni and Fe-
17Cr-9Ni steels after exposure to deaerated high-temperature high-pressure steam at 600° …
17Cr-9Ni steels after exposure to deaerated high-temperature high-pressure steam at 600° …
Advances in corrosion-resistant thermal spray coatings for renewable energy power plants: Part II—Effect of environment and outlook
High-temperature corrosion of critical components such as water walls and superheater
tubes in biomass/waste-fired boilers is a major challenge. A dense and defect-free thermal …
tubes in biomass/waste-fired boilers is a major challenge. A dense and defect-free thermal …
Microstructural understanding of the oxidation of an austenitic stainless steel in high-temperature steam through advanced characterization
It is well-known that steels always oxidize faster in the environments containing water
vapour than in dry oxygen. Due to the difficulties in obtaining necessary experimental scale …
vapour than in dry oxygen. Due to the difficulties in obtaining necessary experimental scale …
[HTML][HTML] Insights into the design of oxidation-resistant Mg alloy by alloying with rare-earth elements
The strategy of rare-earth elements addition into Mg alloys has been successfully developed
and applied to enhance the mechanical performance and corrosion resistance of Mg alloys …
and applied to enhance the mechanical performance and corrosion resistance of Mg alloys …
The origin of different morphology of internal oxide precipitates in ferritic and austenitic steels
The internal oxide precipitates were supposed to be spherical in Wagner's original theory,
while the following research demonstrated that this assumption is an exception rather than …
while the following research demonstrated that this assumption is an exception rather than …
High temperature erosion–oxidation of Cr3C2–NiCr thermal spray coatings under simulated turbine conditions
S Matthews, B James, M Hyland - Corrosion science, 2013 - Elsevier
Most erosion–oxidation research has been directed at high erodent flux, low impact velocity
conditions typical of fluidised bed conditions. Few works have investigated erosion …
conditions typical of fluidised bed conditions. Few works have investigated erosion …
The effect of grain boundary structure on the intergranular degradation behavior of solution annealed alloy 690 in high temperature, hydrogenated water
The environmental degradation of four different types of grain boundaries were investigated
on alloy 690 following slow strain rate tensile tests in 360° C hydrogenated water. Random …
on alloy 690 following slow strain rate tensile tests in 360° C hydrogenated water. Random …
A study on the high-temperature oxidation of ZM6 alloy through advanced characterization
The oxidation of ZM6 alloy in 20% O 2+ Ar at 500℃ was investigated by advanced
characterization. The surface oxide scale had a duplex structure: a MgO outer layer and a …
characterization. The surface oxide scale had a duplex structure: a MgO outer layer and a …
Exploration on the Stress‐induced Internal Corrosion of NaCl-deposited GH4169 under humid intermediate temperature environments
W Wang, Y Cui, R Liu, L Liu, F Wang - Corrosion Science, 2023 - Elsevier
The internal corrosion penetration of GH4169 with NaCl-deposited in humid environments
was analyzed by graded times, stress levels and temperatures. Dynamic principles are …
was analyzed by graded times, stress levels and temperatures. Dynamic principles are …
The third-element effect in the oxidation of Ni–xCr–7Al (x= 0, 5, 10, 15 at.%) alloys in 1 atm O2 at 900–1000° C
Y Niu, XJ Zhang, Y Wu, F Gesmundo - Corrosion science, 2006 - Elsevier
The oxidation in 1atm of pure oxygen of Ni–Cr–Al alloys with a constant aluminum content of
7at.% and containing 5, 10 and 15at.% Cr was studied at 900 and 1000° C and compared to …
7at.% and containing 5, 10 and 15at.% Cr was studied at 900 and 1000° C and compared to …