Laser techniques for dissimilar joining of aluminum alloys to steels: A critical review
The use of multi-materials structures is nowadays one of the most sought solutions to
decrease weight and reduce both emission of greenhouse gases and fuel consumption in …
decrease weight and reduce both emission of greenhouse gases and fuel consumption in …
The hardness and strength properties of WC-Co composites
RW Armstrong - Materials, 2011 - mdpi.com
The industrially-important WC-Co composite materials provide a useful, albeit complicated
materials system for understanding the combined influences on hardness and strength …
materials system for understanding the combined influences on hardness and strength …
Instrumented and Vickers indentation for the characterization of stiffness, hardness and toughness of zirconia toughened Al2O3 and SiC armor
Highlights•We used indentation testing and microscopy to characterize ZTA and
SiC.•Moduli, hardness, toughness were measured at low, intermediate and high loads …
SiC.•Moduli, hardness, toughness were measured at low, intermediate and high loads …
Two-step sintering of fine alumina–zirconia ceramics
CJ Wang, CY Huang, YC Wu - Ceramics International, 2009 - Elsevier
This work investigates the feasibility to the fabrication of high density of fine alumina–5wt.%
zirconia ceramics by two-step sintering process. First step is carried out by constant-heating …
zirconia ceramics by two-step sintering process. First step is carried out by constant-heating …
Nanomechanical filler functionality enables ultralow wear polytetrafluoroethylene composites
Surprisingly, certain α-phase alumina filler particles at one to five weight percent can reduce
the wear rate of polytetrafluoroethylene (PTFE) by 10,000 times, while other, seemingly …
the wear rate of polytetrafluoroethylene (PTFE) by 10,000 times, while other, seemingly …
Micromechanical properties and microstructures of AC and DC flash-sintered alumina
Abstract Alumina (α-Al 2 O 3), one of the most widely used structural ceramics for industrial
applications, requires high temperature and long sintering time to achieve a fully dense …
applications, requires high temperature and long sintering time to achieve a fully dense …
Hard and tough carbon nanotube-reinforced zirconia-toughened alumina composites prepared by spark plasma sintering
J Echeberria, N Rodríguez, J Vleugels, K Vanmeensel… - Carbon, 2012 - Elsevier
It is demonstrated that 0.1 wt% of multi-walled carbon nanotubes (MWCNTs) or single-
walled carbon nanotubes (SWCNTs) added to zirconia toughened alumina (ZTA) …
walled carbon nanotubes (SWCNTs) added to zirconia toughened alumina (ZTA) …
A comparative study of nano-fillers to improve toughness and modulus of polymer-derived ceramics
Brittleness is a major limitation of polymer-derived ceramics (PDCs). Different concentrations
of three nanofillers (carbon nanotubes, Si3N4 and Al2O3 nanoparticles) were evaluated to …
of three nanofillers (carbon nanotubes, Si3N4 and Al2O3 nanoparticles) were evaluated to …
Micromechanical finite element modeling of compressive fracture in confined alumina ceramic
DH Warner, JF Molinari - Acta Materialia, 2006 - Elsevier
A two-dimensional finite element model is developed to investigate intergranular fracture in
alumina under compression. The grain interiors are modeled as anisotropic elastic and the …
alumina under compression. The grain interiors are modeled as anisotropic elastic and the …
A statistical investigation of the effects of grain boundary properties on transgranular fracture
RH Kraft, JF Molinari - Acta Materialia, 2008 - Elsevier
A two-dimensional finite-element model is developed to investigate transgranular fracture in
polycrystalline alumina under tensile loading. Microcracking is modeled explicitly using the …
polycrystalline alumina under tensile loading. Microcracking is modeled explicitly using the …