Precipitation kinetics in metallic alloys: Experiments and modeling
A Deschamps, CR Hutchinson - Acta Materialia, 2021 - Elsevier
Nanoscale precipitation is one of the most widely used microstructural tools to manipulate
the properties of metallic alloys, and especially to reach high strength. Optimal …
the properties of metallic alloys, and especially to reach high strength. Optimal …
Synergy of multiple precipitate/matrix interface structures for a heat resistant high-strength Al alloy
High strength aluminum alloys are widely used but their strength is reduced as nano-
precipitates coarsen rapidly in medium and high temperatures, which greatly limits their …
precipitates coarsen rapidly in medium and high temperatures, which greatly limits their …
Strength and stability through variable micro segregation behaviour of Ta and Zr solutes at intermetallic interfaces in Al-Cu alloys
A small amount of Zr and Ta are added to aluminium-copper (Al-Cu) alloys, and the
evolution of strengthening phases with multi-step heat-treatment and their stability after …
evolution of strengthening phases with multi-step heat-treatment and their stability after …
[HTML][HTML] Microstructure evolution, mechanical property response and strengthening mechanism induced by compositional effects in Al–6 Mg alloys
Y Wang, B Yang, M Gao, E Zhao, R Guan - Materials & Design, 2022 - Elsevier
Based on the compositional design concept, an Al–6 Mg–0.8 Mn (–0.2 Sc) alloy with a good
combination of strength and ductility was obtained by hot extrusion deformation with a large …
combination of strength and ductility was obtained by hot extrusion deformation with a large …
Remarkable improvement in strength and ductility of Al-Cu foundry alloy by submicron-sized TiC particles
Abstract The Al-4.5 Cu alloy reinforced by submicron-sized TiC particles (TiC p) was
fabricated by initially in-situ synthesizing Al–5TiC master alloy, and then incorporating …
fabricated by initially in-situ synthesizing Al–5TiC master alloy, and then incorporating …
Influence of Fe-rich phases and precipitates on the mechanical behaviour of Al-Cu-Mn-Fe-Sc-Zr alloys studied by synchrotron X-ray and neutron
A multiscale methodology using scanning and transmission electron microscope,
synchrotron X-ray nano-tomography and micro-tomography, small angle neutron scattering …
synchrotron X-ray nano-tomography and micro-tomography, small angle neutron scattering …
Effect of Mn content on the microstructure and corrosion resistance of Al-Cu-Mg-Mn alloys
J Fu, K Cui - Journal of Alloys and Compounds, 2022 - Elsevier
Abstract Effect of Mn content on the microstructure and corrosion resistance of Al-Cu-Mg-Mn
alloys was examined by optical microscope (OM), scanning electron microscope (SEM) …
alloys was examined by optical microscope (OM), scanning electron microscope (SEM) …
Enhanced long-term thermal stability and mechanical properties of twin-roll cast Al–Mg–Si alloys with Mn and Cu additions
X Liu, YL Ma, X Wang, SY Zhang, MX Zhang… - Materials Science and …, 2023 - Elsevier
The long-term thermal stability of Al–Mg–Si alloy is of great significance for its engineering
application. In this work, the effects of Mn and Cu on the microstructure and mechanical …
application. In this work, the effects of Mn and Cu on the microstructure and mechanical …
Enhanced precipitation kinetics in non-stretched Al-Cu-Li-Mg-Ag-(Sc)-(Zr) alloys
This work investigates the impact of Sc and Zr on the precipitation kinetics in an Al-Cu-Li
alloy in the absence of pre-stretching. Modern Al-Cu-Li alloys usually require pre-stretching …
alloy in the absence of pre-stretching. Modern Al-Cu-Li alloys usually require pre-stretching …
Hot Tearing analysis and process optimisation of the fire face of Al-Cu alloy cylinder head based on MAGMA numerical simulation
C Yang, H Xu, Y Wang, F Li, H Mao, S Liu - Materials Technology, 2023 - Taylor & Francis
This paper proposes a casting improvement process to enable the casting of Al-Cu alloy
cylinder heads to achieve the required quality. The hot tearing defects generated in the fire …
cylinder heads to achieve the required quality. The hot tearing defects generated in the fire …