Fatigue Damage Assessment and Lifetime Prediction of Short Fiber Reinforced Polymer Composites—A Review
This paper reviews the findings in the area of fatigue damage assessment and lifetime
prediction of short fiber reinforced polymer composites (SFRPs) under cyclic loading. It is …
prediction of short fiber reinforced polymer composites (SFRPs) under cyclic loading. It is …
[HTML][HTML] Carbon fibre sheet moulding compounds with high in-mould flow: Linking morphology to tensile and compressive properties
LM Martulli, L Muyshondt, M Kerschbaum… - Composites Part A …, 2019 - Elsevier
In-mould flow during manufacturing of Sheet Moulding Compounds (SMCs) heavily affects
the material microstructure and its mechanical properties. This influence is studied here for …
the material microstructure and its mechanical properties. This influence is studied here for …
[HTML][HTML] Integrative analysis for prediction of process-induced, orientation-dependent tensile properties in a stochastic prepreg platelet molded composite
Prepreg platelet molded composite (PPMC) is derived from compression molded pieces of
chopped unidirectional prepreg tape. The properties of a stochastic PPMC arise from the …
chopped unidirectional prepreg tape. The properties of a stochastic PPMC arise from the …
[HTML][HTML] A thick-walled sheet moulding compound automotive component: Manufacturing and performance
LM Martulli, T Creemers, E Schöberl, N Hale… - Composites Part A …, 2020 - Elsevier
Abstract Carbon Fibre Sheet Moulding Compounds (CF-SMCs) are lightweight materials
very suitable for automotive parts. So far, their use was limited to thin components. This work …
very suitable for automotive parts. So far, their use was limited to thin components. This work …
[HTML][HTML] Advanced process simulation of compression molded carbon fiber sheet molding compound (C-SMC) parts in automotive series applications
V Romanenko, M Duhovic, D Schommer… - Composites Part A …, 2022 - Elsevier
The following paper focuses on the development of a 3D virtual process chain (VPC) for
parts made from Carbon Fiber Sheet Molding Compounds (C-SMC). The VPC consists of …
parts made from Carbon Fiber Sheet Molding Compounds (C-SMC). The VPC consists of …
Mechanical anisotropy of graphene nanocomposites induced by graphene alignment during stereolithography 3D printing
K Markandan, IP Seetoh, CQ Lai - Journal of Materials Research, 2021 - Springer
Stereolithographically 3D-printed graphene-PMMA nanocomposites were previously found
to be mechanically stiffer and stronger in the print axis, suggesting that the graphene filler …
to be mechanically stiffer and stronger in the print axis, suggesting that the graphene filler …
Fracture analysis of chopped carbon fiber sheet molding compound composite under tensile loading via in-situ μXCT
This paper investigated the crack initiation in a chopped carbon fiber sheet molding
compound (SMC) composite under different tensile loads by integrating synchrotron micro-X …
compound (SMC) composite under different tensile loads by integrating synchrotron micro-X …
[HTML][HTML] Fatigue behavior of hybrid continuous-discontinuous fiber-reinforced sheet molding compound composites under application-related loading conditions
M Bartkowiak, M Kizak, WV Liebig… - Composites Part C: Open …, 2022 - Elsevier
Hybrid continuous-discontinuous sheet molding compound (SMC) composites are
considered suitable candidates for structural automotive applications, due to their high mass …
considered suitable candidates for structural automotive applications, due to their high mass …
[HTML][HTML] Weld lines in tow-based sheet moulding compounds tensile properties: Morphological detrimental factors
LM Martulli, M Kerschbaum, SV Lomov… - Composites Part A …, 2020 - Elsevier
Weld lines (WLs) are among the most detrimental defects affecting polymer composites.
While they have been extensively studied in short fibre composites, their effects on tow …
While they have been extensively studied in short fibre composites, their effects on tow …
[HTML][HTML] Effects of temperature on the anisotropic mechanical properties and failure mechanisms of Sheet Molding Compounds
K Zulueta, I Madina, U Astobitza, A Arrillaga… - Composites Part A …, 2024 - Elsevier
Abstract Sheet Molding Compounds (SMC) are widely used in many industries. Due to their
high in-mold flow, fibers tend to align during the component processing and generate …
high in-mold flow, fibers tend to align during the component processing and generate …