Oxidation behavior characteristics of an aluminized Ni-based single crystal superalloy CM186LC between 900 C and 1100 C in air
FH Latief, K Kakehi, Y Tashiro - Journal of Industrial and Engineering …, 2013 - Elsevier
Oxidation behavior of an aluminized Ni-based single crystal superalloy CM186LC was
performed between 900° C and 1100° C in air. The oxidation kinetics approximately …
performed between 900° C and 1100° C in air. The oxidation kinetics approximately …
Mechanically alloyed metals
H Bhadeshia - Materials science and technology, 2000 - Taylor & Francis
Mechanical alloying involves the severe deformation of mixtures of powders until they form
the most intimate of atomic solutions. Inert oxides can also be introduced to form a uniform …
the most intimate of atomic solutions. Inert oxides can also be introduced to form a uniform …
The study of AA2024 de-alloying using luminol electrogenerated chemiluminescence imaging
N Wint, ZS Barrett, G Williams… - Journal of The …, 2019 - iopscience.iop.org
This paper describes the use of luminol electrogenerated chemiluminescence (ECL) to
image the re-distribution of electrochemically active copper (copper in electrical contact with …
image the re-distribution of electrochemically active copper (copper in electrical contact with …
dissolution rate and Mechanism of Metals in Molten aluminum alloy a380
H Zhu - 2014 - search.proquest.com
Shot sleeve is a very easily worn out part in a high-pressure die-casting machine due to
serious dissolution of the area underneath the pouring hole. It is because during a normal …
serious dissolution of the area underneath the pouring hole. It is because during a normal …
Effect of angle of impingement on air jet erosion wear behavior of chill cast aluminum-boron carbide composites
In the present investigation, the effect of angle of impingement on the air jet erosion wear
behavior of chill cast aluminum boron carbide composites have been studied under room …
behavior of chill cast aluminum boron carbide composites have been studied under room …
Surface Treatment of Fe–30Cr and High Temperature Oxidation
S Chevalier, C Houngninou, O Heintz… - … XVIII: Proceedings of …, 2023 - taylorfrancis.com
Surface treatment was used to improve the high temperature oxidation resistance of an Fe–
30Cr alloy. It was covered with iron aluminides using a pack cementation process. The …
30Cr alloy. It was covered with iron aluminides using a pack cementation process. The …
Optimization of post weld heat treatment cycle of fiber laser welded bainitic steel
JP Gautam - E3S Web of Conferences, 2020 - e3s-conferences.org
Automobile industry has always been in look out for advanced materials that would account
for greater crash resistance, high fatigue strength, optimum ductility and longer service life …
for greater crash resistance, high fatigue strength, optimum ductility and longer service life …
EBSD studies on iron-rich UxFeyBz compounds
Borides play an increasingly important role in the present day engineering due to their high
melting temperatures and chemical and thermal stability. A special case of interest is the …
melting temperatures and chemical and thermal stability. A special case of interest is the …
Damage assessment of process heater tube by magnetic technique: a case study
A Mitra - 2001 - eprints.nmlindia.org
Ferromagnetic properties of steel change with the microstructure, composition and the stress
state of the materials. Such variations are also taking place when the steel components are …
state of the materials. Such variations are also taking place when the steel components are …
Effects of stress on intergranular corrosion and intergranular stress corrosion cracking in AA2024-T3
X Liu - 2005 - rave.ohiolink.edu
High strength AA2024-T3 alloy has pronounced susceptibility to intergranular corrosion
(IGC) and intergranular stress corrosion cracking (IGSCC), which seriously limits the lifetime …
(IGC) and intergranular stress corrosion cracking (IGSCC), which seriously limits the lifetime …