Quantifying primary recrystallization from EBSD maps of partially recrystallized states of an IF steel
A Ayad, M Ramoul, AD Rollett, F Wagner - Materials Characterization, 2021 - Elsevier
A set of IF steel specimens, at several stages of recrystallization, were subjected to EBSD
analysis to provide data for a study of primary recrystallization. First, a criterion was defined …
analysis to provide data for a study of primary recrystallization. First, a criterion was defined …
Effects of residual elements during the casting process of steel production: a critical review
There is a growing drive within the steel industry to increase scrap usage in the Blast
Furnace (BF)-Basic Oxygen Furnace (BOF) integrated route and extend the scrap-based …
Furnace (BF)-Basic Oxygen Furnace (BOF) integrated route and extend the scrap-based …
Deformation and recrystallization behavior of the new Ni-Co based superalloy ingot material prepared by electron beam smelting layered solidification
H Cui, Y Tan, R Bai, L Ning, X You, C Cui… - Journal of Alloys and …, 2023 - Elsevier
The hot deformation behavior of a Ni-Co based superalloy prepared by electron beam
smelting layered solidification (EBSL-Ni-Co superalloy) was studied by hot compression …
smelting layered solidification (EBSL-Ni-Co superalloy) was studied by hot compression …
Disparity in recrystallization of α-& γ-fibers and its impact on Cube texture formation in non-oriented electrical steel
An investigation into the recovery and recrystallization of the two major texture fibres, namely
α and γ, during annealing yielded subtle differences between the two. It is reported that with …
α and γ, during annealing yielded subtle differences between the two. It is reported that with …
[HTML][HTML] Microstructure, precipitate and property evolution in cold-rolled Ti-V high strength low alloy steel
X Zhang, GH ten Brink, A Navarro-López, J Wormann… - Materials & Design, 2020 - Elsevier
A cold-rolled Ti-V high strength low alloy (HSLA) steel was isothermally annealed at 650° C
and 700° C for different times. A unique combination of techniques including visible light …
and 700° C for different times. A unique combination of techniques including visible light …
EBSD investigation of the crystallographic features of deformation-induced martensite in stainless steel
Variant selection during the martensitic transformation in steels may play an important role in
determining the transformation kinetics and the resulting mechanical properties. In this …
determining the transformation kinetics and the resulting mechanical properties. In this …
[HTML][HTML] Study on microstructure evolution and mechanical properties of high-strength low-alloy steel welds realized by flash butt welding thermomechanical …
Defects would occur in the weld joint of the wheel rims during the post-flash butt welding
(FBW) process suffering from poor plasticity, which will deteriorate the quality and lifecycle of …
(FBW) process suffering from poor plasticity, which will deteriorate the quality and lifecycle of …
Correlative analysis of interaction between recrystallization and precipitation during sub-critical annealing of cold-rolled low-carbon V and Ti–V bearing microalloyed …
In this paper a new insight into fundamentals of static recrystallization, precipitation and their
interaction during sub-critical annealing of three cold-rolled low-carbon microalloyed steel …
interaction during sub-critical annealing of three cold-rolled low-carbon microalloyed steel …
Effect of Residual Elements during the Hot‐Working Process of Steel Production: A Critical Review
Demand for steel scrap as feedstock for steelmaking increases, allowing the production of
steel with lower energy costs and reduced CO2 emissions. In general, steel scrap may …
steel with lower energy costs and reduced CO2 emissions. In general, steel scrap may …
[HTML][HTML] Mechanisms for microstructural evolution of FeSiCrNi high silicon steel subjected to thermomechanical processing
H Feng, T Wang, J Han, S Jiang, B Yan, D Sun, P Lin… - Materials & Design, 2024 - Elsevier
Abstract Fe-6.5 wt% Si high silicon steel alloy presents excellent soft magnetic
performances, but a poor plasticity limits its industrial application seriously. In this work, a …
performances, but a poor plasticity limits its industrial application seriously. In this work, a …