Micromanufacturing of composite materials: a review
Composite materials exhibit advantages from the combination of multiple properties, which
cannot be achieved by a monolithic material. At present, the use of composite materials in …
cannot be achieved by a monolithic material. At present, the use of composite materials in …
Formability of austenitic and ferritic stainless steels at warm forming temperature
The warm temperature drawability of austenitic (STS 304) and ferritic stainless (STS 430)
steel sheet samples was evaluated using the cup drawing test. The measured limiting …
steel sheet samples was evaluated using the cup drawing test. The measured limiting …
An experimental investigation into the warm deep-drawing process on laminated sheets under various grain sizes
E Afshin, M Kadkhodayan - Materials & Design, 2015 - Elsevier
It has been proved by many researchers that increasing the temperature in warm deep-
drawing process of single layer sheets decreases the forming load, however, this …
drawing process of single layer sheets decreases the forming load, however, this …
Predictive modeling of spring-back behavior in V-Bending of SS400 steel sheets under elevated temperatures using combined hardening laws
QH Trieu, GH Vuong, DT Nguyen - Applied Sciences, 2023 - mdpi.com
This research presents an innovative methodology for accurately predicting spring-back
tendencies in V-bending of SS400 steel sheets under elevated temperatures. The study …
tendencies in V-bending of SS400 steel sheets under elevated temperatures. The study …
Improvements in springback control by external force laser-assisted sheet bending of titanium and aluminum alloys
The present investigation deals with an external-force laser assisted bending process of
Grade 2 CP titanium and AA 7075 T6 aluminum sheets. High bending angles, sharp fillet …
Grade 2 CP titanium and AA 7075 T6 aluminum sheets. High bending angles, sharp fillet …
Influences of temperature and grain size on the material deformability in microforming process
This paper investigated the influences of temperature and grain size on the deformability of
pure copper in micro compression process. Based on the dislocation theory, a constitutive …
pure copper in micro compression process. Based on the dislocation theory, a constitutive …
Possibilities of application of incremental sheet-forming technique in aircraft industry
T Trzepieciński, B Krasowski, A Kubit… - … in Mechanical and …, 2018 - czasopisma.prz.edu.pl
The article includes the characteristics of incremental forming of the sheet using the
following two methods: Single Point Incremental Forming and Two Point Incremental …
following two methods: Single Point Incremental Forming and Two Point Incremental …
Enhancing combined cryogenic mechanical properties of metastable austenitic stainless steel by warm forming
Q Lu, J Zheng, G Huang, K Li, H Ding, Z Wang… - Journal of Materials …, 2021 - Elsevier
Forming temperature is an essential factor for metastable austenitic stainless steel (M-ASS)
products to accommodate microstructures and cryogenic mechanical performance. Warm …
products to accommodate microstructures and cryogenic mechanical performance. Warm …
Experimental and numerical analysis of industrial warm forming of stainless steel sheet
T Trzepiecinski, T Malinowski, T Pieja - Journal of Manufacturing Processes, 2017 - Elsevier
In this paper, the development of the industrial forming process of drawpieces is investigated
experimentally and numerically. The drawing process presented in this work was achieved …
experimentally and numerically. The drawing process presented in this work was achieved …
Microstructural changes during static recrystallization of austenitic stainless steel 304L: cellular automata simulation
P Alavi, S Serajzadeh - Metallography, Microstructure, and Analysis, 2020 - Springer
Static recrystallization and microstructural changes in austenitic stainless steel 304L were
studied. The rolling experiments at 200° C were carried out, and then, annealing treatment …
studied. The rolling experiments at 200° C were carried out, and then, annealing treatment …