Durability and corrosion of aluminium and its alloys: overview, property space, techniques and developments
Aluminium (Al) is an important structural engineering material, its usage ranking only behind
ferrous alloys (Birbilis, Muster et al. 2011). The growth in usage and production of Al …
ferrous alloys (Birbilis, Muster et al. 2011). The growth in usage and production of Al …
[PDF][PDF] Epoxy resin based composites, mechanical and tribological properties: A review
SA Bello, JO Agunsoye, SB Hassan, MGZ Kana - Tribology in Industry, 2015 - tribology.rs
High fuel consumption by automobile and aerospace vehicles built from legacy alloys has
been a great challenge to global design and material engineers. This has called for …
been a great challenge to global design and material engineers. This has called for …
[PDF][PDF] Mechanical milling: a top down approach for the synthesis of nanomaterials and nanocomposites
Synthesis of nanomaterials by a simple, low cost and in high yield has been a great
challenge since the very early development of nanoscience. Various bottom and top down …
challenge since the very early development of nanoscience. Various bottom and top down …
Structural evolution during mechanical milling of nanometric and micrometric Al2O3 reinforced Al matrix composites
The morphological and microstructural changes during mechanical milling of Al powder
mixed with 5vol% nanoscaled alumina particles (35nm) were studied. The milling was …
mixed with 5vol% nanoscaled alumina particles (35nm) were studied. The milling was …
[HTML][HTML] Effect of ball-milling process parameters on mechanical properties of Al/Al2O3/collagen powder composite using statistical approach
Chrome containing leather-wastes (CCLW) is a waste obtained from leather industries.
These wastes always produced environmental pollution. However, CCLW can be utilized in …
These wastes always produced environmental pollution. However, CCLW can be utilized in …
X-ray diffraction analysis of a severely plastically deformed aluminum alloy
The crystallite size, lattice microstrain, lattice parameter, and formation of solid solutions of a
nanocrystalline Al93Fe3Cr2Ti2 alloy prepared via mechanical alloying (MA) starting from …
nanocrystalline Al93Fe3Cr2Ti2 alloy prepared via mechanical alloying (MA) starting from …
Review on nanocomposites fabricated by mechanical alloying
MA Taha, RA Youness, MF Zawrah - International Journal of Minerals …, 2019 - Springer
Composites are composed of multiphase materials, where each phase has specific
properties that differ from those of the other phases which can effect on the whole properties …
properties that differ from those of the other phases which can effect on the whole properties …
Finite element modeling of the surface roughness of 5052 Al alloy subjected to a surface severe plastic deformation process
K Dai, J Villegas, Z Stone, L Shaw - Acta Materialia, 2004 - Elsevier
The surface of 5052 Al alloy plates is severely plastically deformed via multiple impacts by
high-velocity tungsten carbide/cobalt (WC/Co) balls in a surface nanocrystallization and …
high-velocity tungsten carbide/cobalt (WC/Co) balls in a surface nanocrystallization and …
Nanocomposites and an extremely hard nanocrystalline intermetallic of Al–Fe alloys prepared by mechanical alloying
Mechanical alloying of Al100− xFex, for x= 2.5, 5, 10, 15 and 201, alloys was carried out for
20h followed by cold consolidation. Mechanical alloying resulted in the formation of …
20h followed by cold consolidation. Mechanical alloying resulted in the formation of …
[PDF][PDF] Mechanical and electrical properties of nano Al-matrix composites reinforced with SiC and prepared by powder metallurgy
MF Zawrah, WM El-Meligy, HA Saudi… - … Res. Appl. Chem, 2022 - biointerfaceresearch.com
Nano Al-matrix composites reinforced with SiC were prepared by powder metallurgy
process. The percentages of added SiC were varied between 0, 2, 4, 6, and 8 wt.%. The …
process. The percentages of added SiC were varied between 0, 2, 4, 6, and 8 wt.%. The …