Microstructure and wear characterization of the Fe-Mo-BC—based hardfacing alloys deposited by flux-cored arc welding

M Bembenek, P Prysyazhnyuk, T Shihab, R Machnik… - Materials, 2022 - mdpi.com
An analysis of common reinforcement methods of machine parts and theoretical bases for
the selection of their chemical composition were carried out. Prospects for using flux-cored …

Fabrication of surface composites on different aluminium alloys via friction stir process-A review report

VK Jain, MK Yadav, AN Siddiquee… - Australian Journal of …, 2023 - Taylor & Francis
Friction stir processing (FSP) is used to enhancing the hardness, tensile strength, corrosion
and wear resistance of the substrate by changing the microstructure and through reinforcing …

Fabrication of a high strength ultra-fine grained Al-Mg-SiC nanocomposite by multi-step friction-stir processing

F Khodabakhshi, AP Gerlich, P Švec - Materials Science and Engineering …, 2017 - Elsevier
In this study, multi-step friction-stir processing (FSP) was employed to fabricate an ultra-fine
grained (UFG) Al-matrix nanocomposite with simultaneously enhanced indentation …

Mechanical and Thermal Neutron Absorbing Properties of B4C/Aluminum Alloy Composites Fabricated by Stir Casting and Hot Rolling Process

D Lee, J Kim, B Park, I Jo, SK Lee, Y Kim, SB Lee… - Metals, 2021 - mdpi.com
In this study, to fabricate neutron shielding material, boron carbide (B4C)-reinforced
aluminum (Al) alloy composites were successfully fabricated by stir casting followed by a hot …

Microstructure and Mechanical Properties of Friction Stir Process Derived Al-TiO2 Nanocomposite

HC Madhu, P Ajay Kumar, CS Perugu… - Journal of Materials …, 2018 - Springer
Aluminum-based composites have many advantages over their conventional counterparts. A
major problem in such composites is the clustering of particles in the matrix. Friction stir …

Microstructural Characterization and Tensile Behavior of Rutile (TiO2)-Reinforced AA6063 Aluminum Matrix Composites Prepared by Friction Stir Processing

SJ Abraham, I Dinaharan, JDR Selvam… - Acta Metallurgica Sinica …, 2019 - Springer
Abstract Rutile (TiO 2) particle-reinforced aluminum matrix composites were prepared by
friction stir processing. The microstructure was studied using conventional and advanced …

Preparation of Al2O3/TiO2 particle-reinforced copper through plasma spraying and friction stir processing

C Li, X Feng, Y Shen, W Chen - Materials & Design, 2016 - Elsevier
In this study, Al 2 O 3/TiO 2 particle-reinforced copper matrix surface composites were
successfully processed via friction stir processing (FSP). A “sandwich” lap joint setup …

Enhanced adsorption capacity of porous titanium dioxide nanoparticles synthetized in alkaline sol

L Scrimieri, L Velardi, A Serra, D Manno, F Ferrari… - Applied Physics A, 2020 - Springer
In recent years, the exploitation of natural resources and industrial development have led to
the production of harmful pollutants. Much of these contaminants end up in water resources …

Designing bipolar anodizing towards white anodic aluminum oxide (AAO)

A Gasco-Owens, D Veys-Renaux, E Rocca - Surfaces and Interfaces, 2024 - Elsevier
Obtaining white anodic aluminum oxide (AAO) is a major challenge in the surface finishing
industry. The present work presents a cost-effective route to design light-scattering …

Metal Matrix Composite Fabricated with 5000 Series Marine Grades of Aluminium Using FSP Technique: State of the Art Review

O Muribwathoho, V Msomi, S Mabuwa - Applied Sciences, 2022 - mdpi.com
Aluminium metal matrix composites have been shown to make significant contributions to
the area of new materials and have become widely accepted in high-tech structural and …