The new challenges of machining Ceramic Matrix Composites (CMCs): Review of surface integrity
Abstract Ceramic Matrix Composites (CMCs) are currently an increasing material choice for
several high value and safety-critical components, fact that has recently originated the need …
several high value and safety-critical components, fact that has recently originated the need …
Abrasive fine-finishing technology
F Hashimoto, H Yamaguchi, P Krajnik, K Wegener… - CIRP annals, 2016 - Elsevier
Abrasive fine-finishing technology is often applied as a final finishing process, and the
selection of the right technology is crucial to obtaining the desired performance of functions …
selection of the right technology is crucial to obtaining the desired performance of functions …
Understanding the machining characteristic of plain weave ceramic matrix composite in ultrasonic-assisted grinding
M Zhang, Z Pang, Y Jia, C Shan - Ceramics International, 2022 - Elsevier
The machining of silicon carbide (SiC) ceramic matrix composites is a significant challenge
because of the severe material damage that may occur during material removal, which might …
because of the severe material damage that may occur during material removal, which might …
Grinding of composite materials
B Zhang, S Lu, M Rabiey, D Axinte, F Bleicher - CIRP Annals, 2023 - Elsevier
Grinding plays an important role in ensuring the final machining quality in the manufacturing
process of composite parts. Problems such as grinding damage, grinding wheel wear and …
process of composite parts. Problems such as grinding damage, grinding wheel wear and …
Development of operations in waterjet technology: A review
Waterjet technology has gained much attention due to its ability to cut almost every material.
The development of operations like milling, spot welding, polishing, etc. has further …
The development of operations like milling, spot welding, polishing, etc. has further …
Effect of fiber orientation on surface characteristics of C/SiC composites by laser-assisted machining
C Zhai, J Xu, Y Hou, G Sun, B Zhao, H Yu - Ceramics International, 2022 - Elsevier
In this paper, the characteristics and mechanism of laser-assisted machining (LAM) of C/SiC
composites with different fiber orientations (0°, 45°, 90°, 135°) are studied. For the purpose …
composites with different fiber orientations (0°, 45°, 90°, 135°) are studied. For the purpose …
Influence of controlled depth abrasive water jet milling on the fatigue behavior of carbon/epoxy composites
Conventional milling during aircraft structural composite repair encourages defect
generation and distortion, causing hindrance in milling depth control and thereby adversely …
generation and distortion, causing hindrance in milling depth control and thereby adversely …
Modelling the cross-sectional profile of the kerf generated in overlapped pass erosion in abrasive waterjet milling of Al6061-T6 alloy
S Adsul, DS Srinivasu - Journal of Manufacturing Processes, 2023 - Elsevier
Machining complex surfaces on difficult-to-cut materials by conventional methods is
challenging due to the issues that arise from both the 'freeform surface generation'and the …
challenging due to the issues that arise from both the 'freeform surface generation'and the …
An investigation into the abrasive waterjet milling circular pocket on titanium alloy
Y Yuan, J Chen, H Gao, X Wang - The International Journal of Advanced …, 2020 - Springer
This paper presents an experimental study on abrasive waterjet (AWJ) milling circular
pockets of the titanium alloy Ti6Al4V workpieces. A material removal model is firstly deduced …
pockets of the titanium alloy Ti6Al4V workpieces. A material removal model is firstly deduced …
[HTML][HTML] Modeling of the material removal and heat affected zone formation in CFRP short pulsed laser processing
H Xu, J Hu - Applied Mathematical Modelling, 2017 - Elsevier
Short pulsed laser milling is a novel method to process the carbon fiber reinforced plastics
(CFRP) which has bad machinability. This paper presents a numerical model studying the …
(CFRP) which has bad machinability. This paper presents a numerical model studying the …