A review on additive manufacturing of ceramic matrix composites

J Sun, D Ye, J Zou, X Chen, Y Wang, J Yuan… - Journal of Materials …, 2023 - Elsevier
Additive manufacturing (AM) of ceramic matrix composites (CMCs) has enabled the
production of highly customized, geometrically complex and functionalized parts with …

[HTML][HTML] Mechanical properties of ceramics reinforced with allotropic forms of carbon

V Morales-Florez, A Dominguez-Rodriguez - Progress in Materials Science, 2022 - Elsevier
For decades, enormous investigation effort has been devoted to the fabrication of new
ceramic matrix composites with enhanced mechanical properties. One of the most explored …

Fabrication of dense zirconia-toughened alumina ceramics through a stereolithography-based additive manufacturing

H Wu, W Liu, R He, Z Wu, Q Jiang, X Song, Y Chen… - Ceramics …, 2017 - Elsevier
We report a novel approach to fabricate dense zirconia-toughened alumina (ZTA) ceramics
with excellent properties via an additive manufacturing process based on stereolithography …

Development and evaluation of Al2O3–ZrO2 composite processed by digital light 3D printing

T Zheng, W Wang, J Sun, J Liu, J Bai - Ceramics International, 2020 - Elsevier
Abstract Digital Light Processing (DLP) is a promising approach to fabricate delicate ceramic
components with high-fidelity structural features. In this work, the alumina and …

Characterization of hot-pressed Ti3SiC2–SiC composites

SH Amiri, MG Kakroudi, T Rabizadeh, MS Asl - International Journal of …, 2020 - Elsevier
Abstract The high-density Ti 3 SiC 2-SiC composites with different SiC volume contents were
fabricated by hot pressing technique under 35 MPa in a vacuum atmosphere at 1550° C for …

Research into the mechanical properties, sintering mechanism and microstructure evolution of Al2O3-ZrO2 composites fabricated by a stereolithography-based 3D …

Z Wu, W Liu, H Wu, R Huang, R He, Q Jiang… - Materials Chemistry and …, 2018 - Elsevier
In this paper, a ceramic suspension with appropriate viscosity was prepared by optimizing
the powder solid content and the dispersant content. An Al 2 O 3-ZrO 2 ceramic green body …

Effect of WC-10Co on cavitation erosion behaviors of AlCoCrFeNi coatings prepared by HVOF spraying

Z Wei, Y Wu, S Hong, J Cheng, L Qiao, J Cheng… - Ceramics …, 2021 - Elsevier
Abstract The (AlCoCrFeNi) 1-X (WC-10Co) X composite coatings were fabricated by HVOF
spraying and their microstructures, mechanical properties and cavitation erosion behaviors …

The effect of temperature on the dry sliding wear behavior of HVOF sprayed nanostructured WC-CoCr coatings

S Hong, Y Wu, B Wang, J Zhang, Y Zheng, L Qiao - Ceramics International, 2017 - Elsevier
The sliding wear properties of high-velocity oxygen-fuel (HVOF) sprayed nanostructured WC-
CoCr cermet coatings against Al 2 O 3 under dry friction at different temperatures were …

Fabrication, microstructural and mechanical characterization of Luffa Cylindrical Fibre-Reinforced geopolymer composite

M Alshaaer, SA Mallouh, Y Al-Faiyz, T Fahmy… - Applied Clay …, 2017 - Elsevier
This study reports on the preparation, microstructure, density and mechanical properties of
new geopolymer composites (LG-composite) that are unidirectionally and randomly …

Microstructure and Young's modulus evolution during re-sintering of partially sintered alumina-zirconia composites (ATZ ceramics)

E Gregorova, L Semradova, I Sedlářová… - Journal of the European …, 2021 - Elsevier
Partially and fully sintered alumina-zirconia composites (ATZ ceramics), with porosities
decreasing from 53.5 to 1%, have been prepared by uniaxial pressing and firing at 1000 …