Microstructure and properties of laser cladding NiCrBSi coating assisted by electromagnetic-ultrasonic compound field
G Hu, Y Yang, R Sun, K Qi, X Lu, J Li - Surface and Coatings Technology, 2020 - Elsevier
To improve the defects of element segregation and the uneven microstructure of the laser
cladding layer, the direct current electric field, alternating magnetic field, and ultrasonic field …
cladding layer, the direct current electric field, alternating magnetic field, and ultrasonic field …
A new approach to simulate coating thickness in cold spray
In the process of cold spray on complex components, the coating thickness is an important
indicator to monitor and control. Current methods such as destructive tests or direct …
indicator to monitor and control. Current methods such as destructive tests or direct …
A thermo-mechanical model for simulating the temperature and stress distribution during laser cladding process
Z Zhang, R Kovacevic - The International Journal of Advanced …, 2019 - Springer
During the laser cladding process, thermal stresses are induced because of the high-energy
input, high temperature gradient, fast cooling rate, and inconsistency of the clad-substrate …
input, high temperature gradient, fast cooling rate, and inconsistency of the clad-substrate …
Direct writing of lateral fluorographene nanopatterns with tunable bandgaps and its application in new generation of moiré superlattice
One of the primary goals for monolayer device fabrications and an ideal model of graphene
as an atomic thin “canvas” is one that permits semiconducting/insulating lateral …
as an atomic thin “canvas” is one that permits semiconducting/insulating lateral …
Impact of Microstructure on Remelting Parameters and Mechanical Behavior of Thermally Sprayed NiCrBSi Coating
KA Habib, DL Cano, J Serrano-Mira… - Journal of Thermal …, 2024 - Springer
The present study concerns controlling and quantifying the impact of the remelting thermos-
cycle curve parameters on the microstructure evolution and mechanical properties of …
cycle curve parameters on the microstructure evolution and mechanical properties of …
A novel reverse-polarity plasma torch with extended hot-wall nozzle for atmospheric plasma spraying of dense yttria-stabilized zirconia coatings
F Liu, D Yu, Y Chen, B Duan, J Yao - Surface and Coatings Technology, 2022 - Elsevier
Due to the high heating temperature and low cost, atmospheric plasma spraying (APS) has
been widely used in the preparation of ceramic coatings, but its coatings are normally …
been widely used in the preparation of ceramic coatings, but its coatings are normally …
Numerical investigation of residual stress in plasma sprayed antifriction wear-resistant sealing coatings on GH4169 superalloy substrate
J Wang, Y Zhang, Y Cui, Z Zhai, L Chen, J Lu - Materials Today …, 2022 - Elsevier
Spraying an antifriction wear-resistant sealing coating (AWSC) on the rotor track is an ideal
way to improve wear resistance of finger seal. In this paper, spraying the bond coating (BC) …
way to improve wear resistance of finger seal. In this paper, spraying the bond coating (BC) …
Analysis of thermal-mechanical causes of abrasive belt grinding for titanium alloy
K Song, G Xiao, S Chen, S Li - The International Journal of Advanced …, 2021 - Springer
The abrasive belt grinding process is a highly nonlinear dynamic change process. The
coupling action mechanism between mechanical field and thermal field during grinding is …
coupling action mechanism between mechanical field and thermal field during grinding is …
Optimization and analysis of pyrene-maltose functionalized graphene surfaces for Con A detection
Utilizing the non-covalent π-π stacking of pyrene functionalized molecules onto graphene
surfaces has achieved great success in the detection of various bio-objects, while the …
surfaces has achieved great success in the detection of various bio-objects, while the …
Optimization of the machining process of NiCrBSi thermal spraying
T Zatloukal, J Řehoř, J Fulemova, M Povolný - 2020 - dspace5.zcu.cz
Nowadays, the requirements for the properties of machine parts are increasing. With this
trend, the application of thermal spraying is also growing. The main reason for the use of …
trend, the application of thermal spraying is also growing. The main reason for the use of …