Binder jet 3D printing—Process parameters, materials, properties, modeling, and challenges
As a non-beam-based additive manufacturing (AM) method, binder jet 3D printing (BJ3DP)
is a process in which a liquid binder is jetted on layers of powdered materials, selectively …
is a process in which a liquid binder is jetted on layers of powdered materials, selectively …
Review of non-reactive and reactive wetting of liquids on surfaces
Wettability is a tendency for a liquid to spread on a solid substrate and is generally
measured in terms of the angle (contact angle) between the tangent drawn at the triple point …
measured in terms of the angle (contact angle) between the tangent drawn at the triple point …
Controlling process instability for defect lean metal additive manufacturing
The process instabilities intrinsic to the localized laser-powder bed interaction cause the
formation of various defects in laser powder bed fusion (LPBF) additive manufacturing …
formation of various defects in laser powder bed fusion (LPBF) additive manufacturing …
[HTML][HTML] Interface formation and bonding control in high-volume-fraction (TiC+ TiB2)/Al composites and their roles in enhancing properties
HY Yang, Z Wang, LY Chen, SL Shu, F Qiu… - Composites Part B …, 2021 - Elsevier
As interfaces play a more important role in high-volume-fraction ceramic/metal composites
because of containing more hetero-phase interfaces, it is a great challenge to control the …
because of containing more hetero-phase interfaces, it is a great challenge to control the …
Nanoparticle-enabled phase control for arc welding of unweldable aluminum alloy 7075
Lightweight materials are of paramount importance to reduce energy consumption and
emissions in today's society. For materials to qualify for widespread use in lightweight …
emissions in today's society. For materials to qualify for widespread use in lightweight …
Manufacturing of biomorphic (Si, Ti, Zr)-carbide ceramics by sol–gel processing
Biomorphic (wood derived) carbide ceramics with an overall composition in the systems
MeC/C (with Me= Si, Ti, Zr) were produced by vacuum infiltration of low viscosity organo …
MeC/C (with Me= Si, Ti, Zr) were produced by vacuum infiltration of low viscosity organo …
Study on nano-treating of Al-Mg-Si-Cu alloys with TiC nanoparticles
The 6xxx series wrought aluminum alloys (Al-Mg-Si-Cu) provide good formability and high
strength potential, especially with high Cu additions. However, the large freezing ranges of …
strength potential, especially with high Cu additions. However, the large freezing ranges of …
[HTML][HTML] Effect of lithium anti-ablation and grain refinement introduced by TiC nanoparticles in LPBF Al–Li alloy
Al–Li alloys are extensively utilized in the field of aerospace due to their low density and
high specific strength. However, laser powder bed fusion (LPBF) processed Al–Li alloys still …
high specific strength. However, laser powder bed fusion (LPBF) processed Al–Li alloys still …
Mg/TiC composites manufactured by pressureless melt infiltration
A Contreras, VH Lopez, E Bedolla - Scripta materialia, 2004 - Elsevier
Molten Mg was pressurelessly infiltrated into TiC preforms (56 vol.%) under flowing Ar at
temperatures of 850, 900 and 950° C. The rate of infiltration exhibited a strong temperature …
temperatures of 850, 900 and 950° C. The rate of infiltration exhibited a strong temperature …
Fabrication and mechanical properties of pressureless melt infiltrated magnesium alloy composites reinforced with TiC and Ti2AlC particles
B Anasori, NC El'ad, MW Barsoum - Materials Science and Engineering: A, 2014 - Elsevier
Herein we report on the fabrication and mechanical properties of Mg composites fabricated
by pressureless melt infiltration of Mg and Mg alloys into porous preforms of TiC and Ti 2 …
by pressureless melt infiltration of Mg and Mg alloys into porous preforms of TiC and Ti 2 …