Evaluating mechanical properties and crack resistance of CrN, CrTiN, CrAlN and CrTiAlN coatings by nanoindentation and scratch tests
Abstract CrN, CrTiN, CrAlN and CrTiAlN coatings were deposited on Si (100) wafers, and
their microstructure, mechanical properties, fracture toughness and adhesive strength were …
their microstructure, mechanical properties, fracture toughness and adhesive strength were …
Mechanical, wear, corrosion and biological properties of arc deposited titanium nitride coatings
Cathodic arc deposition of ceramic coatings is gaining importance due to their good
adhesion and minimum residual stresses. In this work we have arc deposited TiN coatings …
adhesion and minimum residual stresses. In this work we have arc deposited TiN coatings …
Effect of Ar/N2 flow ratio on the microstructure and mechanical properties of Ti-Cr-N coatings deposited by DC magnetron sputtering on AISI D2 tool steels
Ti-Cr-N coatings were deposited on Si (100) and AISI D2 tool steel substrates by reactive
DC magnetron co-sputtering technique from titanium and chromium target in mixed Ar/N 2 …
DC magnetron co-sputtering technique from titanium and chromium target in mixed Ar/N 2 …
Annealing effects on microstructural, optical, and mechanical properties of sputtered CrN thin film coatings: experimental studies and finite element modeling
Chromium nitride (CrN) coatings were deposited by magnetron sputtering onto Si (100)
substrates. The coatings were then annealed at different temperatures (500–800° C in steps …
substrates. The coatings were then annealed at different temperatures (500–800° C in steps …
Influence of boron contents on mechanical properties and high-temperature tribological behavior in (AlCrNbTiB) N coatings
TL Chen, SY Hsu, YT Lai, SY Chang… - Journal of Vacuum …, 2023 - pubs.aip.org
Various boron contents of AlCrNbTiBN coatings were prepared by radiofrequency reactive
magnetron cosputtering on both 304 stainless steel and 100 silicon substrates. Boron-doped …
magnetron cosputtering on both 304 stainless steel and 100 silicon substrates. Boron-doped …
The impact of Ni and Mo on growth-morphology and mechanical properties of arc evaporated Ti-Cr-N hard coatings
AV Chernogor, FF Klimashin, AO Volkhonskii… - Surface and Coatings …, 2019 - Elsevier
We studied the growth-morphology, structure, mechanical and tribological properties of Ti
0.43 Cr 0.57 N 0.92, Ti 0.35 Cr 0.65 N 0.78/Ni 0.003, and Ti 0.13 Cr 0.74 Mo 0.13 N 0.71/Ni …
0.43 Cr 0.57 N 0.92, Ti 0.35 Cr 0.65 N 0.78/Ni 0.003, and Ti 0.13 Cr 0.74 Mo 0.13 N 0.71/Ni …
Tribotechnical and mechanical properties of CrN/TiN multi-layer coatings deposited on the surface of die steel
A Leonov, Y Denisova, V Denisov… - AIP Conference …, 2022 - pubs.aip.org
The paper presents the results of studies of CrN/TiN multi-layer coatings on Cr12MoV cold
work die steel deposited by vacuum-arc plasma-assisted method. All coatings were …
work die steel deposited by vacuum-arc plasma-assisted method. All coatings were …
Analysis of the structure of multilayer nanocrystalline coatings based on plasma mass transfer parameters calculated by the Monte Carlo method
AV Chernogor, IV Blinkov, DS Belov… - Technical Physics …, 2019 - Springer
The results of the simulation of plasma fluxes onto the surface of rotating substrates during
the combustion of a vacuum arc of the Cr–Ti–Mo cathode system are presented. The …
the combustion of a vacuum arc of the Cr–Ti–Mo cathode system are presented. The …
Анализ структуры многослойных нанокристаллических покрытий на основе параметров массопереноса плазмы, вычисленных методом Монте-Карло
АВ Черногор, ИВ Блинков, ДС Белов… - Письма в журнал …, 2019 - mathnet.ru
Представлены результаты моделирования плазменных потоков на поверхность
вращающихся подложек при горении вакуумной дуги катодной системы Cr–Ti–Mo …
вращающихся подложек при горении вакуумной дуги катодной системы Cr–Ti–Mo …
Nanoscale multi-layer thin film fabricated by Cathodic Arc Evaporation (CAE) method
In the present study, TiN and CrN single-layer and TiN/CrN nanoscale multi-layer thin films
have been deposited on 420C stainless steel (SS) substrate using a cathodic arc …
have been deposited on 420C stainless steel (SS) substrate using a cathodic arc …