Development of low-cost titanium alloys: A chronicle of challenges and opportunities
MO Bodunrin, LH Chown, JA Omotoyinbo - Materials Today: Proceedings, 2021 - Elsevier
The production of titanium alloys became fully commercialized in the 1950s and that was
precisely 145 years since titanium ores, ilmenite and rutile were first discovered. In the …
precisely 145 years since titanium ores, ilmenite and rutile were first discovered. In the …
Dynamic transformation during the high temperature deformation of titanium alloys
B Guo, JJ Jonas - Journal of Alloys and Compounds, 2021 - Elsevier
Dynamic transformation was first predicted by Gegel and Nadiv during hot deformation of a
Ti-6Al-2Sn-4Zr-2Mo alloy. Later it was observed in near alpha and two-phase titanium …
Ti-6Al-2Sn-4Zr-2Mo alloy. Later it was observed in near alpha and two-phase titanium …
Characterization of microstructure and mechanical properties of laser melting deposited Ti–6.5 Al–3.5 Mo–1.5 Zr–0.3 Si titanium alloy
Y Zhu, D Liu, X Tian, H Tang, H Wang - Materials & Design (1980-2015), 2014 - Elsevier
Abstract A plate of Ti–6.5 Al–3.5 Mo–1.5 Zr–0.3 Si (TC11) titanium alloy is fabricated by laser
melting deposition process. Grain morphology and microstructure characteristics and the …
melting deposition process. Grain morphology and microstructure characteristics and the …
Understanding the microstructure evolution and mechanical behavior of titanium alloy during electrically assisted plastic deformation process
Titanium alloys are widely used in aerospace, petrochemical, and automobile industry due
to their outstanding mechanical properties. However, the formability/plasticity of most …
to their outstanding mechanical properties. However, the formability/plasticity of most …
Characterization of hot deformation behavior of a new near beta titanium alloy: Ti-7333
JK Fan, HC Kou, MJ Lai, B Tang, H Chang, JS Li - Materials & Design, 2013 - Elsevier
The hot deformation behavior of Ti-7333 titanium alloy in the temperature range of 770–970°
C and strain rate range of 10− 3-10 s− 1 has been investigated by hot compressive testing …
C and strain rate range of 10− 3-10 s− 1 has been investigated by hot compressive testing …
Incorporating dynamic recrystallization into a crystal plasticity model for high-temperature deformation of Ti-6Al-4V
During hot deformation of (α+ β) titanium alloys, the simultaneous action of strain and
temperature in the (α+ β) regime facilitates dynamic recovery, dynamic recrystallization …
temperature in the (α+ β) regime facilitates dynamic recovery, dynamic recrystallization …
High-temperature deformation behavior of Ti60 titanium alloy
W Jia, W Zeng, Y Zhou, J Liu, Q Wang - Materials Science and Engineering …, 2011 - Elsevier
Isothermal compressions of near-alpha Ti60 alloy were carried out on a Gleeble-3800
simulator in the temperature range of 960–1110° C and strain rate range of 0.001–10.0 s− 1 …
simulator in the temperature range of 960–1110° C and strain rate range of 0.001–10.0 s− 1 …
Ultrafine grain formation in a Ti-6Al-4V alloy by thermomechanical processing of a martensitic microstructure
In the current study, ultrafine equiaxed grains with a size of 150 to 800 nm were successfully
produced in a Ti-6Al-4V alloy through thermomechanical processing of a martensitic starting …
produced in a Ti-6Al-4V alloy through thermomechanical processing of a martensitic starting …
Deformation behavior and microstructural evolution of as-cast 904L austenitic stainless steel during hot compression
Y Han, G Liu, D Zou, R Liu, G Qiao - Materials Science and Engineering: A, 2013 - Elsevier
Hot compression tests of as-cast 904L austenitic stainless steel were carried out at
deformation temperatures of 1000–1150° C and strain rates of 0.01–10s− 1 with different …
deformation temperatures of 1000–1150° C and strain rates of 0.01–10s− 1 with different …
[HTML][HTML] Hyperbolic–sine constitutive model determined hot deformation mechanisms and workability response of Al–Zn/Cu and Al–Zn/SiC based composites
The response to hot deformation of Al–Zn-based composites reinforced with copper (Al–
Zn/6Cu) and silicon carbide (Al–Zn/8SiC) particles was investigated. The composites were …
Zn/6Cu) and silicon carbide (Al–Zn/8SiC) particles was investigated. The composites were …