An approach towards energy and material efficient additive manufacturing: Multi-objective optimization of stellite-6 deposition on SS304
Energy and material saving in additive manufacturing (AM) has become the main concern in
recent times for sustainable manufacturing. In this study, a 2 kW fiber laser was used in the …
recent times for sustainable manufacturing. In this study, a 2 kW fiber laser was used in the …
Scratch hardness at a small scale: Experimental methods and correlation to nanoindentation hardness
Nanoindentation and scratch experiments probe the hardness by leaving a permanent
imprint on the material's surface. The scratch hardness, however, is less used due to its …
imprint on the material's surface. The scratch hardness, however, is less used due to its …
Linac4 H− ion sources
J Lettry, D Aguglia, J Alessi, P Andersson… - Review of scientific …, 2016 - pubs.aip.org
CERN's 160 MeV H− linear accelerator (Linac4) is a key constituent of the injector chain
upgrade of the Large Hadron Collider that is being installed and commissioned. A cesiated …
upgrade of the Large Hadron Collider that is being installed and commissioned. A cesiated …
[HTML][HTML] Scratching the surface: Elastic rotations beneath nanoscratch and nanoindentation tests
In this paper, we investigate the residual deformation field in the vicinity of nanoscratch tests
using two orientations of a Berkovich tip on an (001) Cu single crystal. We compare the …
using two orientations of a Berkovich tip on an (001) Cu single crystal. We compare the …
Influence of sample tilt and applied load on microscratch behavior of copper under a spherical diamond indenter
M Liu - Tribology Letters, 2021 - Springer
Microscratch test with a spherical indenter was carried out on copper under different tilt
conditions and applied loads. Influence of surface slope and applied load on scratch …
conditions and applied loads. Influence of surface slope and applied load on scratch …
Mapping the elastic modulus of a surface with a NanoScan 3D scanning microscope
II Maslenikov, VN Reshetov, AS Useinov - Instruments and experimental …, 2015 - Springer
The possibility of mapping the elasticity modulus during scanning of the material surface
with a piezoresonance probe is proposed. An analytical model is proposed that describes …
with a piezoresonance probe is proposed. An analytical model is proposed that describes …
Alloying and strain hardening effects in abrasive contacts on iron based alloys
Strain hardening is a widely used effect to reduce wear, hence it can be expedient in
tribological contacts. For this work abrasive contacts were simulated in a scratch test at both …
tribological contacts. For this work abrasive contacts were simulated in a scratch test at both …
Material wear map for ground-engaging steels based on scratch tests
The present work examines the scratch resistances of a series of candidate ground-
engaging steels. A range of microstructures is considered: tempered martensite, nano …
engaging steels. A range of microstructures is considered: tempered martensite, nano …
[PDF][PDF] Abrasive wear of alloys for ground engaging tools
G Saha - 2017 - dro.deakin.edu.au
Abrasive wear of alloys for ground engaging tools Page 1 Abrasive wear of alloys for
ground engaging tools AUTHOR(S) Gourab Saha PUBLICATION DATE 01-09-2017 …
ground engaging tools AUTHOR(S) Gourab Saha PUBLICATION DATE 01-09-2017 …
[PDF][PDF] Индентирование. Измерение твердости и трещиностойкости покрытий
А Усеинов, К Кравчук, И Маслеников - Наноиндустрия, 2013 - nanoindustry.su
Свойства алмазоподобных пленок углерода–эпитаксиальных слоев микро-и
нанокристаллического алмаза, а также аморфных пленок углерода зависят от состава …
нанокристаллического алмаза, а также аморфных пленок углерода зависят от состава …