Effect of graphite additives on microstructure and mechanical properties of Al–Cu composites prepared by mechanical alloying and sintering
Al–Cu matrix composites with 5 wt% of graphite nanoplatelets additives were prepared
using mechanical alloying (MA) of elemental Al–Cu–C powder mixtures followed by hot …
using mechanical alloying (MA) of elemental Al–Cu–C powder mixtures followed by hot …
[PDF][PDF] Effect of Al2O3 reinforcement nanoparticles on the tribological behaviour and mechanical properties of Al6061 alloy
HA Al-Salihi, HK Judran - AIMS Mater. Sci, 2020 - academia.edu
Effect of Al 2O3 reinforcement nanoparticles on the tribological behaviour and mechanical
properties of Al6061 alloy Page 1 AIMS Materials Science, 7(4): 486–498. DOI: 10.3934/matersci.2020.4.486 …
properties of Al6061 alloy Page 1 AIMS Materials Science, 7(4): 486–498. DOI: 10.3934/matersci.2020.4.486 …
Effect of carbon in fabrication Al-SiC nanocomposites for tribological application
B Hekner, J Myalski, T Pawlik, M Sopicka-Lizer - Materials, 2017 - mdpi.com
Aluminium-based hybrid composites are a new class of advanced materials with the
potential of satisfying the demands in engineering applications. This paper describes the …
potential of satisfying the demands in engineering applications. This paper describes the …
Evaluating the influence of milling time, and sintering temperature and time on the microstructural changes and mechanical properties of Al-Y2W3O12-AlN hybrid …
The present investigation evaluates the effect of milling time, sintering time (t) and
temperature (T), and amount of reinforcement (R) on the relative density (RD), hardness (H) …
temperature (T), and amount of reinforcement (R) on the relative density (RD), hardness (H) …
Effect of vanadium on enhancing the mechanical and wear behaviour of copper by using stir casting technique
J Jabinth, N Selvakumar - Materials Research Express, 2019 - iopscience.iop.org
A primary element of copper is dispersed with a secondary element (vanadium) by stir
casting technique. This alloy is melted in a furnace and the percentage of Vanadium is …
casting technique. This alloy is melted in a furnace and the percentage of Vanadium is …
Study on effect of EAFD particulate reinforcement in AA7075 aluminum matrix composites
EO Alves, DRA Amaro, ECO Silva… - Materials …, 2018 - SciELO Brasil
Eletric arc furnace dust is dangerous solid waste that is generated in steel manufacturing
processes. The utilization of the dust from these industries avoids disposing it into industrial …
processes. The utilization of the dust from these industries avoids disposing it into industrial …
Increase of the mechanical response of pure aluminum by grain refinement retained with an alternative rapid sintering route
JM Mendoza-Duarte, FC Robles-Hernandez… - Journal of Materials …, 2021 - Springer
High-frequency induction heating is frequently used to consolidate solid pieces of refractory
ceramics. However, this valuable technique has not been deeply evaluated for sample …
ceramics. However, this valuable technique has not been deeply evaluated for sample …
Influence of Graphene, SiCnp, and G/SiCnp Hybrid Fillers on the Strengthening Mechanisms of Al-Matrix
M Shokeir, S El Moghazi, AF Omara… - … Materials Transactions A, 2020 - Springer
AA2124 reinforced with graphene (G), silicon carbide nanoparticles (SiC np), and graphene-
coated SiC np (GCSiC np) were fabricated and characterized. GCSiC np reinforcement was …
coated SiC np (GCSiC np) were fabricated and characterized. GCSiC np reinforcement was …
Analysis and Optimization of Abrasive water Jet Machiningprocesses on the hybrid nano particle reinforced Aluminum alloy matrix composite material
R Venkatesh, VS Rao… - IOP Conference Series …, 2020 - iopscience.iop.org
The Nano hybrid particles reinforced aluminium based MMC has been prepared and
characterized. The materials chosen for the fabrication of the composites include Aluminium …
characterized. The materials chosen for the fabrication of the composites include Aluminium …
Structure and Mechanical Properties of Al–Cu/C Composites Produced by Mechanical Alloying and Solid-State Sintering
Hypoeutectic and eutectic Al–Cu composites with 5% wt. of graphite additives are prepared
using mechanical alloying (MA) of elemental powders and following hot pressing of mixtures …
using mechanical alloying (MA) of elemental powders and following hot pressing of mixtures …