Defining a relationship between pearlite morphology and ferrite crystallographic orientation
This study involved fully pearlitic wires of seven different diameters (5.5–1.6 mm). All
samples were laboratory annealed to re-austenitize and were then air-cooled to reform the …
samples were laboratory annealed to re-austenitize and were then air-cooled to reform the …
On the surface residual stress measurement in magnesium alloys using X-ray diffraction
A Yazdanmehr, H Jahed - Materials, 2020 - mdpi.com
X-ray penetration in magnesium alloys is significant due to the low X-ray mass attenuation
coefficient. To measure the surface residual stresses in magnesium alloys, a correction …
coefficient. To measure the surface residual stresses in magnesium alloys, a correction …
Influences of Al and Ti particles on microstructure, internal stress and property of Ni composite coatings
Abstract Ternary Ni—xAl—yTi (x, y in weight percent) composite coatings with different
amounts of mixed Al and Ti particles were prepared by electrodeposition. The influences of …
amounts of mixed Al and Ti particles were prepared by electrodeposition. The influences of …
Hot isostatic pressing influence on the mechanical properties of selectively laser-melted 316L steel
Industries that rely on additive manufacturing of metallic parts, especially biomedical
companies, require material science-based knowledge of how process parameters and …
companies, require material science-based knowledge of how process parameters and …
Mechanical properties analysis of the AA2519-AA1050-Ti6Al4V explosive welded laminate
Explosively welded layered materials made of (a) an AA2519 aluminum alloy (AlCuMgMn+
ZrSc),(b) titanium alloy Ti6Al4V and (c) an intermediate layer composed of a thin aluminum …
ZrSc),(b) titanium alloy Ti6Al4V and (c) an intermediate layer composed of a thin aluminum …
Experimental characterization and finite element modeling of through thickness deformation gradient in a cold rolled zirconium sheet
A commercial Zirconium alloy was subjected to different thickness reductions (20%, 40%
and 60%) by cold rolling. A through-thickness gradient in microstructure, crystallographic …
and 60%) by cold rolling. A through-thickness gradient in microstructure, crystallographic …
Through-thickness deformation gradient in a Part-Pilgered Zirconium Tube: experimental measurements and numerical validation
Through-thickness microstructure development and residual stress evolution were explored
in a part-pilgered Zircaloy-4 tube. Clear gradients in microstructure and residual stress were …
in a part-pilgered Zircaloy-4 tube. Clear gradients in microstructure and residual stress were …
Microstructure and residual stresses of AA2519 friction stir welded joints under different heat treatment conditions
The aim of this research was to investigate the effect of different heat treatment conditions of
AA2519 friction stir welded joints on their microstructure and residual stresses. The following …
AA2519 friction stir welded joints on their microstructure and residual stresses. The following …
Hard and Corrosion-Resistant Ni-xAl-yTi Nanocomposite Coatings for CNT/Al Composites
Y Zhao, C Wang, L Wang, Z Xu, C Jiang - Journal of Materials Engineering …, 2017 - Springer
Abstract The ternary Ni-x Al-y Ti (x, y in wt.%) nanocomposite protective coatings were
electroplated on carbon nanotubes (CNT)/Al composite by the co-deposition of Al and Ti …
electroplated on carbon nanotubes (CNT)/Al composite by the co-deposition of Al and Ti …
Burst ductility of zirconium clads: The defining role of residual stress
Closed end burst tests, using room temperature water as pressurizing medium, were
performed on a number of industrially produced zirconium (Zr) clads. A total of 31 samples …
performed on a number of industrially produced zirconium (Zr) clads. A total of 31 samples …