Thermomechanical processing of advanced high strength steels
J Zhao, Z Jiang - Progress in Materials Science, 2018 - Elsevier
Advanced high strength steels (AHSSs) are regarded as the most promising materials for
vehicles in the 21st century. AHSSs are complex and sophisticated materials, with …
vehicles in the 21st century. AHSSs are complex and sophisticated materials, with …
Towards understanding the brittle–ductile transition in the extreme manufacturing
T Zhang, F Jiang, H Huang, J Lu, Y Wu… - … Journal of Extreme …, 2021 - iopscience.iop.org
The brittle–ductile transition (BDT) widely exists in the manufacturing with extremely small
deformation scale, thermally assisted machining, and high-speed machining. This paper …
deformation scale, thermally assisted machining, and high-speed machining. This paper …
Texture evolution during high strain-rate compressive loading of maraging steels produced by laser powder bed fusion
Dynamic mechanical behavior and texture evolution in maraging steels, manufactured using
the laser powder bed fusion (LPBF) technique, was investigated at strain rates of 2000 s− 1 …
the laser powder bed fusion (LPBF) technique, was investigated at strain rates of 2000 s− 1 …
Effects of prior ECAP process on the dynamic impact behaviors of hypereutectic Al-Si alloy
The dynamic mechanical responses of as-cast and ECAPed hypereutectic Al-Si alloy
subjected to high strain rate compression by split Hopkinson pressure bar (SHPB) system …
subjected to high strain rate compression by split Hopkinson pressure bar (SHPB) system …
Investigations on mechanical properties and microstructural examination of activated TIG-welded nuclear grade stainless steel
S Mohan Kumar, S Sankarapandian… - Journal of the Brazilian …, 2020 - Springer
Nuclear grade austenitic stainless steel 321 contains titanium for severe corrosive
conditions and is used for process equipment, aircraft exhaust manifolds and boiler shells …
conditions and is used for process equipment, aircraft exhaust manifolds and boiler shells …
Introducing both chemical and structural gradients in AISI 321 stainless steel via aluminizing and laser shock peening for superior properties
L Yu, W Jiang, X An, S Ni, G Bo, W Li, M Song - Surface and Coatings …, 2023 - Elsevier
Aluminizing is a diffusion based chemical surface treatment on materials to provide excellent
protection against high temperature oxidation and corrosion, but is likely to be accompanied …
protection against high temperature oxidation and corrosion, but is likely to be accompanied …
Deformation mechanism and texture evolution of a low-Ni Cr–Mn–N austenitic stainless steel under bending deformation
H Kamali, H Xie, H Bi, E Chang, H Xu, H Yu… - Materials Science and …, 2021 - Elsevier
The detailed evolution of microstructure and texture of a low-Ni Cr–Mn–N austenitic
stainless steel under bending deformation was studied. The effect of austenite grain …
stainless steel under bending deformation was studied. The effect of austenite grain …
Direct drive friction welding effect on mechanical and electrochemical characteristics of titanium stabilized austenitic stainless steel (AISI 321) research reactor thick …
NE Titouche, T Boukharouba, SA Amzert… - Journal of Manufacturing …, 2019 - Elsevier
Well known for its good weldability by conventional welding techniques and also for its strain
hardening ability, titanium stabilized austenitic stainless steel (AISI 321) thick tube in a …
hardening ability, titanium stabilized austenitic stainless steel (AISI 321) thick tube in a …
Modification of mechanical properties of high-strength titanium alloys VT23 and VT23m due to impact-oscillatory loading
A simple technological method is proposed and tested experimentally, which allows for the
improvement of mechanical properties in sheet two-phase high-strength titanium alloys …
improvement of mechanical properties in sheet two-phase high-strength titanium alloys …
Structural evolution of ceramic coatings by mechanical alloying
Z Sagdoldina, B Rakhadilov, M Skakov… - Materials testing, 2019 - degruyter.com
This article researches the formation of ceramic coatings of zirconium dioxide (ZrO2) on a X
12 Cr Ni 18 10 Ti steel surface after mechanical alloying. The study of the coating surfaces …
12 Cr Ni 18 10 Ti steel surface after mechanical alloying. The study of the coating surfaces …