A Bluetooth low-energy transceiver with 3.7-mW all-digital transmitter, 2.75-mW high-IF discrete-time receiver, and TX/RX switchable on-chip matching network
FW Kuo, SB Ferreira, HNR Chen… - IEEE Journal of Solid …, 2017 - ieeexplore.ieee.org
We present an ultra-low-power Bluetooth low-energy (BLE) transceiver (TRX) for the Internet
of Things (IoT) optimized for digital 28-nm CMOS. A transmitter (TX) employs an all-digital …
of Things (IoT) optimized for digital 28-nm CMOS. A transmitter (TX) employs an all-digital …
A review of ultra-low-power and low-cost transceiver design
T Schumacher, M Stadelmayer… - 2017 Austrochip …, 2017 - ieeexplore.ieee.org
This paper reviews trends for ultra-low-power wireless transceiver system and integrated
circuit design under the perspective of using cost-effective CMOS technology nodes. These …
circuit design under the perspective of using cost-effective CMOS technology nodes. These …
An ADPLL-centric bluetooth low-energy transceiver with 2.3 mW interference-tolerant hybrid-loop receiver and 2.9 mW single-point polar transmitter in 65nm CMOS
This paper demonstrates a Bluetooth Low-Energy (BLE) transceiver (TRX) achieving ultra-
low-power (ULP) operation for Internet-of-Things (IoT) applications. As more and more …
low-power (ULP) operation for Internet-of-Things (IoT) applications. As more and more …
Bluetooth Communication Leveraging Ultra-Low Power Radio Design
Energy-efficient wireless connectivity plays an important role in scaling both battery-less and
battery-powered Internet-of-Things (IoT) devices. The power consumption in these devices …
battery-powered Internet-of-Things (IoT) devices. The power consumption in these devices …
An ultralow-power current-reused direct-conversion Bluetooth-low-energy receiver front-end in 40-nm CMOS
AHM Shirazi, HM Lavasani… - IEEE Transactions …, 2021 - ieeexplore.ieee.org
An ultralow-power direct-conversion Bluetooth-low-energy (BLE) receiver (RX) front-end that
employs current-reuse and subthreshold techniques is presented. A stacked and self-biased …
employs current-reuse and subthreshold techniques is presented. A stacked and self-biased …
Analysis and Design of Reactive Passive Mixers for High-Order Modulation IoT Cartesian Transmitters
The growth of the Internet of Things (IoT) is calling for more efficient, higher data rate radios.
However, the high-order modulations required to push the data rates, while increasing the …
However, the high-order modulations required to push the data rates, while increasing the …
A 980μW 5.2 dB-NF current-reused direct-conversion bluetooth-low-energy receiver in 40nm CMOS
AHM Shirazi, HM Lavasani… - 2017 IEEE Custom …, 2017 - ieeexplore.ieee.org
This work presents a 980μW direct-conversion BLE receiver at a 1V supply, employing
current-reuse and subthreshold techniques. The receiver has a measured noise figure of 5.2 …
current-reuse and subthreshold techniques. The receiver has a measured noise figure of 5.2 …
Design and analysis of a DCO-based phase-tracking RF receiver for IoT applications
YH Liu, VK Purushothaman… - IEEE Journal of Solid …, 2019 - ieeexplore.ieee.org
This paper presents an energy-/area-efficient digitally controlled oscillator (DCO)-based
phase-tracking Receiver for Internet-of-Things (IoT) applications. The RX leverages the …
phase-tracking Receiver for Internet-of-Things (IoT) applications. The RX leverages the …
System design of a 2.75-mW discrete-time superheterodyne receiver for Bluetooth low energy
This paper introduces a system-level approach to develop the first-ever fully discrete-time
(DT) superheterodyne receiver (RX) for Internet-of-Things applications, such as Bluetooth …
(DT) superheterodyne receiver (RX) for Internet-of-Things applications, such as Bluetooth …
Design of a 0.6-V, 429-MHz FSK transceiver using Q-enhanced and direct power transfer techniques in 90-nm CMOS
CY Chiu, ZC Zhang, TH Lin - IEEE Journal of Solid-State …, 2020 - ieeexplore.ieee.org
A 429-MHz ultra low-power frequency-shift keying (FSK) transceiver (TRX) that is operated
at 0.6 V at 200 kb/s is presented in this work. The receiver (RX) used in this work uses a …
at 0.6 V at 200 kb/s is presented in this work. The receiver (RX) used in this work uses a …