Nanoindentation. Mechanical engineering series
AC Fischer-Cripps… - Appl. Mech. Rev., 2004 - asmedigitalcollection.asme.org
The equations of balance of momentum and energy usually are formulated under the
assumption of conservation of mass. However, mass is not conserved when sources of mass …
assumption of conservation of mass. However, mass is not conserved when sources of mass …
[HTML][HTML] Polymerization shrinkage stress of composite resins and resin cements–What do we need to know?
CJ Soares, MP RODRIGUES, ABF VILELA… - Brazilian oral …, 2017 - SciELO Brasil
Polymerization shrinkage stress of resin-based materials have been related to several
unwanted clinical consequences, such as enamel crack propagation, cusp deflection …
unwanted clinical consequences, such as enamel crack propagation, cusp deflection …
Cold sintered ceramic nanocomposites of 2D MXene and zinc oxide
Nanocomposites containing 2D materials have attracted much attention due to their
potential for enhancing electrical, magnetic, optical, mechanical, and thermal properties. 2D …
potential for enhancing electrical, magnetic, optical, mechanical, and thermal properties. 2D …
Scaling, dimensional analysis, and indentation measurements
YT Cheng, CM Cheng - Materials Science and Engineering: R: Reports, 2004 - Elsevier
We provide an overview of the basic concepts of scaling and dimensional analysis, followed
by a review of some of the recent work on applying these concepts to modeling instrumented …
by a review of some of the recent work on applying these concepts to modeling instrumented …
Relationships between hardness, elastic modulus, and the work of indentation
YT Cheng, CM Cheng - Applied physics letters, 1998 - pubs.aip.org
The work done during indentation is examined using dimensional analysis and finite
element calculations for conical indentation in elastic-plastic solids with work hardening. An …
element calculations for conical indentation in elastic-plastic solids with work hardening. An …
Review of functionally graded thermal sprayed coatings
The paper briefly describes major thermal spray techniques used to spray functionally
graded coatings such as atmospheric plasma spraying, high velocity oxy-fuel spraying …
graded coatings such as atmospheric plasma spraying, high velocity oxy-fuel spraying …
Measurement of the microhardness and Young's modulus of human enamel and dentine using an indentation technique
N Meredith, M Sherriff, DJ Setchell… - Archives of Oral Biology, 1996 - Elsevier
Conventional quasi-static and dynamic test methods have a number of limitations when
used to measure the mechanical properties of enamel and dentine. These are due to the …
used to measure the mechanical properties of enamel and dentine. These are due to the …
Effect of cation composition on the mechanical stability of perovskite solar cells
Photoactive perovskite semiconductors are highly tunable, with numerous inorganic and
organic cations readily incorporated to modify optoelectronic properties. However, despite …
organic cations readily incorporated to modify optoelectronic properties. However, despite …
The deformation behavior of ceramic crystals subjected to very low load (nano) indentations
TF Page, WC Oliver, CJ McHargue - Journal of Materials research, 1992 - cambridge.org
The ultra-low load indentation response of ceramic single crystal surfaces (Al2O3, SiC, Si)
has been studied with a software-controlled hardness tester (Nanoindenter) operating in the …
has been studied with a software-controlled hardness tester (Nanoindenter) operating in the …
Porosity-dependence of elastic moduli and hardness of 3Y-TZP ceramics
J Luo, R Stevens - Ceramics International, 1999 - Elsevier
The elastic moduli and Vickers hardness of porous 3Y-TZP ceramics have been measured
and related to a computed model. At the low porosity level (less than 8%), the spherical …
and related to a computed model. At the low porosity level (less than 8%), the spherical …