Hot deformation behavior and constitutive modeling of fine grained Inconel 718 superalloy

YB Tan, YH Ma, F Zhao - Journal of Alloys and Compounds, 2018 - Elsevier
The hot deformation behavior of fine grained Inconel 718 superalloy was investigated by
compression test in the temperature range of 950 to 1150° C and strain rate range of 0.1–10 …

Hot-working behavior of an advanced intermetallic multi-phase γ-TiAl based alloy

E Schwaighofer, H Clemens, J Lindemann… - Materials Science and …, 2014 - Elsevier
New high-performance engine concepts for aerospace and automotive application enforce
the development of lightweight intermetallic γ-TiAl based alloys with increased high …

Dynamic softening behavior of TC18 titanium alloy during hot deformation

YQ Ning, BC Xie, HQ Liang, H Li, XM Yang, HZ Guo - Materials & Design, 2015 - Elsevier
Dynamic softening behavior of TC18 titanium alloy have been investigated in this paper
based on isothermal compression experiment. Strain-rate sensitivity coefficient m and …

Characterization of hot deformation behavior of as-cast TC21 titanium alloy using processing map

Y Zhu, W Zeng, F Feng, Y Sun, Y Han… - Materials Science and …, 2011 - Elsevier
The hot deformation behavior of as-cast TC21 titanium alloy has been investigated in the
isothermal compression of the alloy using processing maps conducted at the deformation …

Hot deformation behaviour of Ti alloys: A review on physical simulation and deformation mechanisms

P Yadav, KK Saxena, S Sehgal… - Proceedings of the …, 2023 - journals.sagepub.com
Titanium and its alloys, owing to their properties like high strength, toughness, corrosion
resistance and thermal stability, are employable in various engineering and medical …

Effect of temperature and strain rate on hot deformation behavior and microstructure of Al-Cu-Li alloy

N Nayan, SVSN Murty, S Chhangani, A Prakash… - Journal of Alloys and …, 2017 - Elsevier
Abstract Al-Cu-Li alloy (AA2195) was produced using vacuum induction melting (VIM)
furnace under dynamic argon atmosphere. The as-cast billets were homogenized using a …

Hot deformation behavior and processing map of a powder metallurgy Ti–22Al–25Nb alloy

J Jia, K Zhang, L Liu, F Wu - Journal of alloys and compounds, 2014 - Elsevier
Abstract Powder metallurgy (P/M) Ti–22Al–25Nb alloy billets were fabricated by hot pressing
(HP) from argon atomized pre-alloyed powders at a temperature of 1050° C under a …

Analysis of metal workability by integration of FEM and 3-D processing maps

J Liu, Z Cui, C Li - Journal of Materials Processing Technology, 2008 - Elsevier
Workability consists of two independent parts: state-of-stress (SOS) workability and intrinsic
workability. The traditional processing maps proposed by Prasad on the base of dynamic …

Characterization of high-temperature deformation behavior of as-cast Ti60 titanium alloy using processing map

W Peng, W Zeng, Q Wang, H Yu - Materials Science and Engineering: A, 2013 - Elsevier
Isothermal compression testing of as-cast Ti60 titanium alloy is carried out at the deformation
temperature range of 970–1120° C with 50° C intervals, strain rate range of 0.01–10s− 1 …

Hot deformation and processing maps of an Al–5.7 wt.% Mg alloy with erbium

G Meng, B Li, H Li, H Huang, Z Nie - Materials Science and Engineering: A, 2009 - Elsevier
The hot deformation behavior of an Al–5.7 wt.% Mg alloy with erbium has been investigated.
Compression tests are performed in the temperature range of 300–500° C and in the strain …