Research status and prospect of friction stir processing technology
K Li, X Liu, Y Zhao - Coatings, 2019 - mdpi.com
Friction stir processing (FSP) is a novel solid-phase processing technique that is derived
from friction stir welding (FSW). The microstructure of the base metal can be modified with …
from friction stir welding (FSW). The microstructure of the base metal can be modified with …
Friction stir processing influence on microstructure, mechanical, and corrosion behavior of steels: A review
Friction stir processing (FSP) technology has received reasonable attention in the past two
decades to process a wide range of materials such as aluminum, magnesium, titanium …
decades to process a wide range of materials such as aluminum, magnesium, titanium …
A study on microstructural, mechanical properties and optimization of wear behavior of friction stir processed AlCrCoFeNi High Entropy Alloy reinforced SS410 using …
Abstract The equimolar High Entropy Alloy (HEA) is incorporated on the surface of SS410
steel to enhance the mechanical properties for the current industrial scenario. The objective …
steel to enhance the mechanical properties for the current industrial scenario. The objective …
A study on microstructural, mechanical properties, and optimization of wear behaviour of friction stir processed AZ31/TiC composites using response surface …
The primary objective of this study is to investigate the microstructural, mechanical, and wear
behaviour of AZ31/TiC surface composites fabricated through friction stir processing (FSP) …
behaviour of AZ31/TiC surface composites fabricated through friction stir processing (FSP) …
[HTML][HTML] Critical review on advanced cooling strategies in friction stir processing for microstructural control
Friction stir processing (FSP) stands as an effective approach designed for grain refinement
and site-specific microstructural modification. The evolving microstructure during FSP is …
and site-specific microstructural modification. The evolving microstructure during FSP is …
[HTML][HTML] Investigating the tribological behavior of bioinspired surfaces in agro-waste and alumina reinforced AA6063 matrix composites
F Ben, PA Olubambi - Vacuum, 2024 - Elsevier
The tribological behavior of three bioinspired (BI) agro-waste ashes—bean pod ash (BPA),
cassava peel ash (CPA), and coconut husk ash (CHA)—integrated as reinforcements in an …
cassava peel ash (CPA), and coconut husk ash (CHA)—integrated as reinforcements in an …
Obtaining a wide-strain-range true stress–strain curve using the measurement-in-neck-section method
Background Measuring true stress–strain curve over a large-strain-range is essential to
understand mechanical behavior and simulate non-linear plastic deformation. The digital …
understand mechanical behavior and simulate non-linear plastic deformation. The digital …
Formability behavior of AH-32 shipbuilding steel strengthened by friction stir process
Ships are built by bringing materials into various forms and then joining them. Although
materials such as wood, composite materials, polyethylene, and aluminum alloys are used …
materials such as wood, composite materials, polyethylene, and aluminum alloys are used …
Synergy Study Between a Lubricant Oil Layer and a Microstructural Graphite to Reduce Friction and Wear of a Thermally Modified Low-Carbon Gray Cast-Iron …
FG Mejía Hernández, M Ramírez Cardona… - Tribology …, 2023 - Taylor & Francis
The results of a sliding wear tests on base and thermal treated gray cast iron (GCI) samples
from internal combustion engine cylinder liner are reported here for dry and lubricated …
from internal combustion engine cylinder liner are reported here for dry and lubricated …
[PDF][PDF] Studying the impact of multi-pass friction stir processing on microstructure and mechanical properties of low-carbon steel.
M Moradi, G Khalaj, G Ghaffari… - Metallic Materials/Kovové …, 2023 - kovmat.sav.sk
In this study, plain carbon steel (A216-WCB) was processed using a WC tool with a plunge
depth of 2 mm, an advancing speed of 80 mm min− 1, and a rotational speed of 2800 rpm …
depth of 2 mm, an advancing speed of 80 mm min− 1, and a rotational speed of 2800 rpm …