On the solidification characteristics, deformation, and functionally graded interfaces in additively manufactured hybrid aluminum alloys
AlSi10Mg powder is deposited on top of a cast AA2618 substrate via laser powder bed
fusion technique to form hybrid aluminum parts for additive repair purposes. The …
fusion technique to form hybrid aluminum parts for additive repair purposes. The …
Dendritic arm spacing affecting mechanical properties and wear behavior of Al-Sn and Al-Si alloys directionally solidified under unsteady-state conditions
KS Cruz, ES Meza, FAP Fernandes… - … Materials Transactions A, 2010 - Springer
Abstract Alloys of Al-Sn and Al-Si are widely used in tribological applications such as
cylinder liners and journal bearings. Studies of the influence of the as-cast microstructures of …
cylinder liners and journal bearings. Studies of the influence of the as-cast microstructures of …
Relationship between spacing of eutectic colonies and tensile properties of transient directionally solidified Al-Ni eutectic alloy
Abstract Eutectic Al-Ni alloys are widely faced as materials to be considered for advanced
structural components. Nevertheless, still there is a lack of research on microstructural …
structural components. Nevertheless, still there is a lack of research on microstructural …
Cellular/dendritic arrays and intermetallic phases affecting corrosion and mechanical resistances of an Al–Mg–Si alloy
Abstract Outdoor applications of Al–Mg–Si alloys have been specified due to their very good
corrosion resistance when compared with those of other aluminum alloys. Nevertheless …
corrosion resistance when compared with those of other aluminum alloys. Nevertheless …
The effects of cell spacing and distribution of intermetallic fibers on the mechanical properties of hypoeutectic Al–Fe alloys
The aim of the present investigation was to contribute to provide a basis for understanding
how to control solidification parameters, microstructure and mechanical strength of Al–Fe …
how to control solidification parameters, microstructure and mechanical strength of Al–Fe …
Microstructural development and mechanical properties of a near-eutectic directionally solidified Sn–Bi solder alloy
BL Silva, G Reinhart, H Nguyen-Thi… - Materials …, 2015 - Elsevier
Sn–Bi solders may be applied for electronic applications where low-temperature soldering is
required, ie, sensitive components, step soldering and soldering LEDs. In spite of their …
required, ie, sensitive components, step soldering and soldering LEDs. In spite of their …
Characterization of dendritic microstructure, intermetallic phases, and hardness of directionally solidified Al-Mg and Al-Mg-Si alloys
Despite the widespread application of Al-Mg-Si alloys, especially in the automotive industry,
interrelations of solidification thermal parameters (cooling rate and growth rate) …
interrelations of solidification thermal parameters (cooling rate and growth rate) …
The correlation between dendritic microstructure and mechanical properties of directionally solidified hypoeutectic Al-Ni alloys
Al-Ni hypoeutectic alloys were directionally solidified under upward transient heat flow
conditions. The aim of the present study is to set up correlations between the as-cast …
conditions. The aim of the present study is to set up correlations between the as-cast …
Alloy composition and metal/mold heat transfer efficiency affecting inverse segregation and porosity of as-cast Al–Cu alloys
Porosity is one of the most important defects in metals casting. In this study,
macrosegregation and porosity formation were investigated by a numerical model and by …
macrosegregation and porosity formation were investigated by a numerical model and by …
Слоистые интерметаллидные композиты и покрытия
ЛМ Гуревич, ВГ Шморгун, ОВ Слаутин, АИ Богданов - 2016 - elibrary.ru
На собственных теоретических и экспериментальных данных, а также материалах
некоторых других исследователей авторы раскрывают механизмы и закономерности …
некоторых других исследователей авторы раскрывают механизмы и закономерности …