Investigations on deformation and fracture behavior of workpiece material during high speed machining of 7050-T7451 aluminum alloy
Research on material deformation and fracture behavior under large strain rate has great
practical significance. The dynamic property of 7050-T7451 aluminum alloy under the strain …
practical significance. The dynamic property of 7050-T7451 aluminum alloy under the strain …
Experimental, modeling, and numerical simulation of ultrasonic assisted drilling of CFRP/Ti stacks
Carbon fiber reinforced polymer (CFRP) and Ti-6Al-4V alloy (Ti) stacks structures are
increasingly utilized in aircraft load-bearing applications, where the quality of hole …
increasingly utilized in aircraft load-bearing applications, where the quality of hole …
Fabrication of Al–Ti–B grain refiner using machining Ti chips, reaction mechanisms and grain refinement performance in pure Al
M Hu, F Wang, B Jiang, H Wang, Y Liu, Z Ji - Metals and Materials …, 2021 - Springer
Abstract Al–5Ti–1B grain refiner was successfully prepared with the reaction of Ti chips
produced during machining and KBF 4 in pure aluminum melt. In order to illustrate the …
produced during machining and KBF 4 in pure aluminum melt. In order to illustrate the …
Effect of CeO2 on Al–Ti–C and matrix conversion between TiC and α-Al orientation relationship
T Liu, M Hu, F Wang, B Jiang, Z Ji - Journal of Materials Science, 2022 - Springer
AT the present study, Al–5Ti–0.25 C–1Ce alloy was prepared by using Al chips, Ti chips,
graphite powder and CeO2 powder as raw materials under different process conditions. The …
graphite powder and CeO2 powder as raw materials under different process conditions. The …
Process for advanced management and technologies of aircraft EOL
C Mascle, P Baptiste, D Sainte Beuve, A Camelot - Procedia CIRP, 2015 - Elsevier
Different possibilities are available to treat aircraft end-of-life (EOL), each with positive and
negative impacts on the 3 spheres of sustainable development. EOL processing includes 4 …
negative impacts on the 3 spheres of sustainable development. EOL processing includes 4 …
Improvement of high-temperature oxidation resistance of titanium-based alloy by sol–gel method
XJ Zhang, YH Gao, BY Ren, N Tsubaki - Journal of materials science, 2010 - Springer
Sol–gel dip coating of SiO 2 was applied on a TiAl-based alloy, and subsequent heat
treatment was performed. XRD and SEM/EDS analysis revealed that an amorphous silica …
treatment was performed. XRD and SEM/EDS analysis revealed that an amorphous silica …
Strain rate analyses during elliptical vibration cutting of Inconel 718 using finite element analysis, Taguchi method, and ANOVA
HB Xie, ZQ Yang, N Qin, ZJ Wang - Advances in Manufacturing, 2020 - Springer
The high strain rate in metal cutting significantly affects the mechanical properties of the
work piece by altering its properties. This study outlines the material strain rates during …
work piece by altering its properties. This study outlines the material strain rates during …
Microstructure and mechanical properties of nano-grained dual-phase Ni-based alloy
YL Sun, LM Fu, LF Lv, RJ Guo, XF Yao… - Materials Science …, 2016 - Trans Tech Publ
To provide insight into the mechanical behavior and microstructural evolution of bulk
nanograined (NG) Ni-based alloys during annealing, the Ni-based alloy sheets with grain …
nanograined (NG) Ni-based alloys during annealing, the Ni-based alloy sheets with grain …
Microstructure and deformation behavior of Ti-10V-2Fe-3Al alloy during hot forming process
R Guan, Z Zhao, KS Choi, CS Lee - Journal of Wuhan University of …, 2015 - Springer
The microstructure evolution and formability of Ti-10V-2Fe-3Al alloy related to the initial
microstructures and processing variables were investigated during hot forming process. The …
microstructures and processing variables were investigated during hot forming process. The …