A review on conventional and nonconventional machining of Nickel-based Nimonic superalloy
Superalloys have gained prominence in recent years in various sectors, namely, spacecraft,
marine, power, defense, vehicular and others, due to their ability to withstand high …
marine, power, defense, vehicular and others, due to their ability to withstand high …
Environment-friendly machining of aerospace-grade Ti alloy using SiAlON ceramic and AlTiN coated carbide inserts under sustainable biodegradable mist condition
A Gautam, G Bartarya, P Dutta - CIRP Journal of Manufacturing Science …, 2022 - Elsevier
Due to lower thermal conductivity and high chemical reactivity Ti6Al4V is considered as the
difficult to machine aerospace material. To improve the machinability both AlTiN coated …
difficult to machine aerospace material. To improve the machinability both AlTiN coated …
Post-processing
Throughout this book we have discussed geometric accuracy, surface finish, and property
limitations of AM. When a part comes out of an AM machine, there may still be a number of …
limitations of AM. When a part comes out of an AM machine, there may still be a number of …
Evaluation of tool wear and surface roughness in high-speed dry turning of Incoloy 800
G Prasad, GS Vijay, R Kamath C - Cogent Engineering, 2024 - Taylor & Francis
Machining of Incoloy 800 is challenging, which can be attributed to the low thermal
conductivity, hot strength, accord for insert material and propensity to work harder. This study …
conductivity, hot strength, accord for insert material and propensity to work harder. This study …
Analysis, modelling and optimization on tool vibration in machining of nitronic 60 with SiAlON ceramic tool
The study investigates tool vibration during finish turning of austenitic steel (Nitronic 60)
using a new-generation SiAlON ceramic cutting insert under dry conditions. Three …
using a new-generation SiAlON ceramic cutting insert under dry conditions. Three …
Surface roughness prediction in hard-turning with ANN and RSM
AE Ahmed, MG Ahmed, M SS - Journal of the Egyptian society of …, 2020 - journals.ekb.eg
In the below investigation, artificial-neural-network (ANN) and response-surface-
methodology (RSM) predictive tools shall be applied for predicting “surface roughness” on …
methodology (RSM) predictive tools shall be applied for predicting “surface roughness” on …
Investigative study of cutting parameters during turning hardened steel with carbide inserts
Traditionally, the turning of hardened steel is accomplished with cutting tools made of
materials like ceramics, cubic boron nitride (CBN), diamond, etc. Due to advances in the …
materials like ceramics, cubic boron nitride (CBN), diamond, etc. Due to advances in the …
Analysis and prediction of tool wear in dry turning of hardened D3 steel using hybrid insert: A novel wear map approach
D Rath, S Panda - … of the Institution of Mechanical Engineers …, 2022 - journals.sagepub.com
Previously cubic boron nitride (CBN) and ceramic inserts were used for the dry turning of
heat-treated D3 tool steel with cutting speed beyond 200 m/min, suffers from severe tool …
heat-treated D3 tool steel with cutting speed beyond 200 m/min, suffers from severe tool …
[PDF][PDF] Optimization of Roundness Error in Hard Turning of AISI H13 Tool Steel
AA Elsadek, AM Gaafer, SS Mohamed - 2020 - jest.journals.ekb.eg
In the current investigation, a novel optimization algorithm, named the Duelist algorithm
(DA), is employed for optimizing the roundness error by the proper selection of the input …
(DA), is employed for optimizing the roundness error by the proper selection of the input …
Effect of chip breaker land width of trapezoidal chip breaking groove on tool vibration caused by chip control
K Zhou, S Chen - … on Mechanical Design and Simulation (MDS …, 2023 - spiedigitallibrary.org
The 3D cutting simulation of Ti6Al4V titanium alloy material by trapezoidal chip breaking
groove tool with different land width was carried out by ABAQUS, and the cutting force in …
groove tool with different land width was carried out by ABAQUS, and the cutting force in …