Fatigue properties of AlSi10Mg produced by additive layer manufacturing
This work shows the impact of microstructure and defect on the fatigue life of an AlSi10Mg
manufactured by Additive Layer Manufacturing (ALM). Samples were manufactured via a …
manufactured by Additive Layer Manufacturing (ALM). Samples were manufactured via a …
Fatigue from defect: influence of size, type, position, morphology and loading
Y Nadot - International Journal of Fatigue, 2022 - Elsevier
The paper, after analysis of a large experimental data base, shows that, depending on the
material, the effect of defect on the fatigue limit should be described through 5 major …
material, the effect of defect on the fatigue limit should be described through 5 major …
Influence of casting defect and SDAS on the multiaxial fatigue behaviour of A356-T6 alloy including mean stress effect
The effect of mean stress on the multiaxial High Cycle Fatigue (HCF) behaviour of cast A356-
T6 alloy containing natural and artificial defects with varying Secondary Dendrite Arming …
T6 alloy containing natural and artificial defects with varying Secondary Dendrite Arming …
Investigation of the effect of porosity on the high cycle fatigue behaviour of cast Al-Si alloy by X-ray micro-tomography
VD Le, N Saintier, F Morel, D Bellett… - International Journal of …, 2018 - Elsevier
Porosity generated by the casting process has a detrimental effect on the high cycle fatigue
strength of cast aluminium alloys. The current study presents an investigation using the non …
strength of cast aluminium alloys. The current study presents an investigation using the non …
Influence of casting defects on the fatigue behavior of cast aluminum AS7G06-T6
P Mu, Y Nadot, C Nadot-Martin, A Chabod… - International Journal of …, 2014 - Elsevier
Abstract AS7G06-T6 cast aluminum alloy is tested under tension fatigue loading for two load
ratios. After the quantification of the Secondary Dendrite Arm Spacing (SDAS) and grain size …
ratios. After the quantification of the Secondary Dendrite Arm Spacing (SDAS) and grain size …
Influence of defect size on the fatigue resistance of AlSi10Mg alloy elaborated by selective laser melting (SLM)
In the aircraft industry, Additive Manufacturing (AM) process is receiving more and more
attention to produce parts with complex geometry and also leads to important weight …
attention to produce parts with complex geometry and also leads to important weight …
Defect-correlated fatigue assessment of A356-T6 aluminum cast alloy using computed tomography based Kitagawa-Takahashi diagrams
Modern aluminum cast alloys are promising candidates for highly loaded lightweight
components due to their good strength-to-weight ratio. To enable a safe design of aluminum …
components due to their good strength-to-weight ratio. To enable a safe design of aluminum …
[HTML][HTML] Fracture–mechanical assessment of the effect of defects on the fatigue lifetime and limit in cast and additively manufactured aluminum–silicon alloys from HCF …
Aluminum–silicon alloys are commonly used in die-cast and additively manufactured (AM)
light-weight components due to their good processability and high strength-to-weight ratio …
light-weight components due to their good processability and high strength-to-weight ratio …
Numerical prediction of fatigue life of an A356-T6 alloy wheel considering the influence of casting defect and mean stress
Y Duan, F Zhang, D Yao, L Tian, L Yang… - Engineering Failure …, 2020 - Elsevier
A fatigue prediction method considering shrinkage cavity, secondary dendrite arm spacing
(SDAS) and mean stress level is presented in the paper. Firstly, the casting process of an …
(SDAS) and mean stress level is presented in the paper. Firstly, the casting process of an …
Multiaxial high cycle fatigue damage mechanisms associated with the different microstructural heterogeneities of cast aluminium alloys
VD Le, F Morel, D Bellett, N Saintier… - Materials Science and …, 2016 - Elsevier
This paper is dedicated to the high cycle fatigue (HCF) behaviour of cast Al–Si alloys. In
particular, three similar alloys with different microstructural characteristics are investigated …
particular, three similar alloys with different microstructural characteristics are investigated …