[HTML][HTML] Age hardening behaviors of spun 2219 aluminum alloy component
ZX Li, M Zhan, XG Fan, XX Wang, F Ma - Journal of Materials Research …, 2020 - Elsevier
The role of spinning in the age hardening behaviors of 2219 aluminum alloy and the
underlying mechanisms are very vital for aging process design. To this end, the Vickers …
underlying mechanisms are very vital for aging process design. To this end, the Vickers …
Mechanical properties improvement of pre-deformed Al–Zn–Mg–Cu alloys by electroshocking treatment based on the non-equilibrium scattering of electron …
W Wu, Y Song, P Zhou, Y Yu, L Xie, L Hua - Journal of Alloys and …, 2021 - Elsevier
Plastic deformation is usually required from raw materials to metal products. Unfortunately,
the lost ductility of high-strength aluminum alloys during deformation can hardly be …
the lost ductility of high-strength aluminum alloys during deformation can hardly be …
[HTML][HTML] Low cycle fatigue properties of Sc-modified AA2519-T62 extrusion
This investigation presents the results of research on low cycle fatigue properties of Sc-
modified AA2519-T62 extrusion. The basic mechanical properties of the investigated alloy …
modified AA2519-T62 extrusion. The basic mechanical properties of the investigated alloy …
[HTML][HTML] Influence of pre-aging on the artificial aging behavior of a 6056 aluminum alloy after conventional extrusion
In the present study, the influence of the initial heat-treatment conditions on the artificial
aging behavior after conventional linear extrusion at room temperature was investigated for …
aging behavior after conventional linear extrusion at room temperature was investigated for …
[HTML][HTML] Study on symmetry and asymmetry rolling of AA2519-T62 alloy at room-temperature and cryogenic conditions
The aim of this investigation was to identify the effect of rolling at room temperature and
under cryogenic conditions on selected properties and the microstructure of the AA2519-T62 …
under cryogenic conditions on selected properties and the microstructure of the AA2519-T62 …
[HTML][HTML] Influence of the Plastic Deformation Process on the Residual Stresses and Hardness of an Al-5Mg Alloy
The service behavior of ductile metallic materials, when they have previously undergone
technological plastic deformation, depends on the deformation conditions. These are …
technological plastic deformation, depends on the deformation conditions. These are …
Nanoscale structural evolution of Al2Cu precipitates in friction-stir welded Al–Cu–Mg alloy
I Zuiko, S Malopheyev, S Mironov… - IOP Conference Series …, 2021 - iopscience.iop.org
The work is devoted to FSW of cold rolled AA2519. The non-uniform distribution of all
second phase precipitates (including coherent θ''and non-coherent θ) was shown via the …
second phase precipitates (including coherent θ''and non-coherent θ) was shown via the …
[PDF][PDF] Influence of Pre-Aging on the Artificial Aging Behavior of a 6056 Aluminum Alloy after Conventional Extrusion. Metals 2021, 11, 385
L Winter, K Hockauf, M Scholze… - doi. org/10.3390 …, 2021 - researchgate.net
In the present study, the influence of the initial heat-treatment conditions on the artificial
aging behavior after conventional linear extrusion at room temperature was investigated for …
aging behavior after conventional linear extrusion at room temperature was investigated for …
Effect of Pre-Straining Method on Mechanical Properties of Thermo-Mechanically Processed Al-Cu-Mg Alloy
I Zuiko, V Kulitckii, R Kaibyshev - Defect and Diffusion Forum, 2018 - Trans Tech Publ
The present study deals with the effect of pre-deformation technique of AA2519 alloy (Al–
5.64 Cu–0.33 Mn–0.23 Mg–0.15 Zr–0.11 Ti–0.09 V–0.08 Fe–0.01 Si (wt.%)) under T8 …
5.64 Cu–0.33 Mn–0.23 Mg–0.15 Zr–0.11 Ti–0.09 V–0.08 Fe–0.01 Si (wt.%)) under T8 …
Effect of ECAP prior to aging on microstructure, precipitation behaviour and mechanical properties of an Al-Cu-Mg alloy
I Zuiko, M Gazizov, R Kaibyshev - Defect and diffusion forum, 2018 - Trans Tech Publ
Microstructure, precipitation behaviour and mechanical properties of an Al-5.64 Cu-0.33 Mn-
0.23 Mg-0.14 Zr-0.11 Ti (in wt.%) alloy subjected to thermomechanical processing (TMP) …
0.23 Mg-0.14 Zr-0.11 Ti (in wt.%) alloy subjected to thermomechanical processing (TMP) …